搜索资源列表
IRDA-contrl
- 本程序是38kHz的红外线发射接收程序。发射部分为AVR单片机,接收部分用51单片机解码。-this procedure is 38KHz infrared transmitting and receiving procedures. Part of the launch of AVR, receiving some 51 microcontroller with decoders.
QT2A
- 用的是飞斯卡尔的一个小单片机,做的一个遥控器接收代码..接收频率是38KHZ-the fly Scalfaro is a small microprocessor, do a remote control receiver code .. receiving frequency is 38 KHZ
length
- 单片机超声波测距程序源代码,38KHZ,可以4M
fasong
- 红外发送程序,适用于一般的红外发光二极管,38KHZ调制
infrared_transmitter
- 自定义编码的红外发射器,采用汉明纠错编码。接收方可实现一位误码的纠错。38KHz发射载波调制,配合红外发射二级管可实现5-10米的数据通信与遥控。
Text1
- 红外遥控发射38Khz的代码,利用51单片机作为控制芯片-Infrared remote control transmitter 38Khz code
geli-kongtiao-yaokongqi
- 格力空调YBOF2型号遥控器的输出码,图为虚拟示波器实测,调制38KHz占空比可适当调节-With PWM technology for temperature control operation, microcontroller programming, Proteus simulation
3ch_remote
- THIS RX PROJECT :3 channel remote control CRYSTAL 4 MHz RC5 FORMAT @38KHz , 35 duty cycle ADDRESS = 0X0B ch1 = 0X01 ch2 = 0X02 ch3 = 0X03 NOT USE TOGGLE ALWAY = 0- THIS IS RX PROJECT :3 channel remote control CRYSTAL
pin
- 小车红外避障 驱动直流电机 38khz红外 小车拐弯、前进功能-IR obstacle avoidance car driving DC motors 38khz infrared car turning, forward function
IrDA
- 用gpl162002的普通io口模拟38kHZ红外发送,接收用串口 -using gpl162002 IO send IRdata
irsend
- 51单片机直接控制红外LED,发出接收头所需的38KHZ的脉冲光。-ir sender used for 51 serious MCU.
38k
- 红外发射管 发射38kHZ的 方波 驱动红外发射管-38khz
hongwaishoufa
- 红外收发演示,红外收发模块检验,频率为38kHz-IR Transceiver Demo
hongwai
- 51单片机红外解码程序 红外遥控38khz解码-51MCU IR decoder
FT-099LD(E)
- 激光650nm接收器资料,接收光为38Khz可调试光-650nm laser data receivers, the received optical light can be debugged to 38Khz
fashe
- 可以启动红外发射头,产生38Khz红外信号,以启动VS0038接收头,接收信号-c language program
wuxianguangxian
- 基于51单片机的无线光线检测系统的源代码,能自动解调38KHZ的红外调制信号,判断亮灭程度。-51 MCU-based wireless light detection system source code, can automatically 38KHZ infrared modulated signal demodulation to determine the degree of light off.
Irda(Send)
- 8051红外发射程序,38KHZ红外发射程序-IR remote control program.
51MCU-The-infrared-signal-analysis
- 基于51单片机的红外信号分析程序,获取的数据在数码管上显示的同时通过串口发送到电脑上,用于帮助并分析未知的红外信号.红外信号38khz.-51 MCU-based infrared signal analysis program to obtain data in digital display at the same time sent to the computer through the serial port, to help and analyze the unknown infrar