搜索资源列表
chengxu
- 基于51单片机的电动门设计(使用8255、输出灯、输入开关、8253定时器、8259中断和步进电机等)-Based on the electric door design 51 single-chip microcomputer(Use 8255, output lamp, input switch, 8253 timers, 8259 interrupt and the stepping motor, etc )
clock
- 用asm汇编语言实现一个日时钟,用到8253中断实现秒跳动,可以从任意时间点开始计时-Asm assembly language with a Japanese clock, interrupt 8253 is used to achieve second beat, you can start from any point in time time
8253stopwatch
- 通过PC机内8253定时器设置时间常数,使其每隔10MS产生一次中断,并通过定时中断 ,接管中断服务程序,由汇编语言实现主程序,中断服务程序的编写。-PC-8253 timer to set the time constant, so that every 10MS generate an interrupt and timer interrupt and take over the interrupt service routine, assembly language main progra
lab9
- 电子钟设计 利用8253定时器用中断方式定时,用8255并行口控制LED数码管的扫描显示及键盘作按钮的时间修改,制做成一个24小时进制的电子钟或表。 利用实验三(定时器)、实验六(中断)、实验五(并行口键盘)、七段数码管显示的线路原理图,用中断方式编程完成一个电子钟或表的设计。 -The design uses 8253 electronic clock timer with interrupt timer, display and keyboard for the button
2013061811111231
- 用PC机内部的中断控制器8259A,中断源用TPC-H实验箱上的8253,使8253每隔4秒产生一次中断请求-Using a PC to the internal interrupt controller 8259A, interrupt source with the TPC-H experimental box 8253, making 8253 every 4 seconds to generate an interrupt request
motor
- 直流电机的转速控制。利用8253产生“准PWM”(占空比50 ~0 )波形,不同的占空比影响着直流电机的转速。通过秒中断服务程序读取K7-0的数据、修改PWM的占空比,实现直流电机的转速控制。 -DC motor speed control. 8253 use a " quasi-PWM" (50 to 0 duty cycle) waveform, affecting different duty DC motor speed. Read by the interru
jiaotongdneg
- 交通信号灯 本程序设计中用到了8253,8255,8259三个芯片。利用8253分频产生0.1S的时钟,8255连接LED灯输出,利用8259产生中断,控制交通灯的状态。-Traffic lights used in the design of this program 8253,8255,8259 three chips. The use of 8253-Divider 0.1S clock, LED light output 8255 connected by 8259 to gener
dianzishizhong
- 该系统是一个简单的利用8253定时器、8255可并行通信接口和中断控制器8259设计的电子时钟系统,在该系统中设有一个启动键,启动键未按下时,显示初始化界面“HELLO”;当按下启动键时,8253定时器开始计时(8253的初值为10000,接1MHz的脉冲,即当8253计满100时正好是1S),当计时计满100时,8259便产生一次中断,在LED显示器便显示系统预先设计好的初始值“23.59.55”便开始从秒位开始加1,当加到10S时,10s位加1,加到60S时分位加1,同时秒位清零,同时怎加到
5
- 8253 通道 0 工作在方式 0(脉冲计数产生中断),由按键产生单脉冲接入 CLK0、令计数初值为 0FH, 手动逐个输入单脉冲,编程在计算机屏幕上显示计数值,并用逻辑笔观察 OUT0 的状态,键盘有键按下时 返回 DOS。-8253 channel 0 0 work in way (pulse counting the interrupt), single pulse generated by the key access CLK0, counting the initial val
实验四前三题
- 1、8255 芯片初始化 (1) 分析原理图,计算 8255 芯片和 8253 芯片在 IO 空间中各内部寄存器的端口地址,修改 Demo 程序(main.asm 和 INTDemo.asm)中 IO 空间地址的符号定义(xxH)。 (2) 分析原理图中 8255 芯片 PA、PB 和 PC 口的信号传输方向确定各端口的输入及输出状 态,填充源代码框架中 8255 芯片初始化子程序 INIT8255,完成 8255 芯片初始化代码。 (3) 分析原理图中 PC 口的电路功能,完成对 PC 口各信