搜索资源列表
adc12_UART
- 对于MSP430F169,采用单通道单次转换方式,对接口板上的一路模拟信号P6.0(0~3.3V可调电压)进行A/D转换,并将12位转换结果通过串口发到PC机,由PC机的串口助手显示出来。-For MSP430F169, the use of single-channel single conversion by means of an interface board all the way analog signal P6.0 (0 ~ 3.3V adjustable voltage) for
ADC
- 将AIN0.0的输入值(电压)转换为12位数字量,保存在片内外部存储器XRAM中,本程序对应的处理器为C8051f020单片机。-Will AIN0.0 input value (voltage) is converted to 12-digit volume, stored in external memory-chip XRAM, this procedure corresponds to single-chip processors for the C8051F020.
ADC
- 实现AD模数转换的程 序 ,用C语言写,-AD achieve analog-digital conversion process, using C language,
adc
- 熟悉A/D转换 软件思路:选择RAO做为模拟输入通道; 连续转换4次再求平均值做为转换结果 最后结构只取低8位 结果送数码管的低3位显示-Familiar with the A/D conversion software ideas: Select RAO as analog input channels consecutive conversion and then seek the average of 4 times as the results of the f
UART0
- C8051F020串口0的调试程序,其内部包含ADC转换调试程序和lcd接口程序-C8051F020 serial 0 debug procedures, its internal ADC converter contains debugging procedures and lcd interface program
Iadc
- PWM同步,ADC模块对电流信号进行采样,在DSP发送PWM脉冲时,给出一个同步信号,经过一定的可编程延时时间后,启动ADC的转换-PWM synchronization, ADC module on the current signal sample, in the DSP to send PWM pulse, give a synchronous signal, after a programmable delay time, start ADC conversion
ADCcdesign
- ADC模数转换,主要是利用Fusion的模数转换模块。-ADC analog-digital conversion, mainly the use of Fusion' s analog-digital conversion module.
ADC
- 单片机AD转换程序,适用于MC9s08AW60,-Single-chip AD conversion process, applicable to MC9s08AW60,
ADC
- 适合学习HCS12系列单片机的初学者使用。 我的环境是DP256,这个程序是将AN01~03的模拟信号转换成数字信号,由PORTB输出。-Study fit HCS12 MCU Series beginners. My environment is DP256, this procedure will AN01 ~ 03 are analog signals into digital signals by the PORTB output.
adc
- 模数转换,可以讲模拟信号转换成二进制数字信号-anolog to digital convertor
AVR_SPI_ADC
- AVR单片机SPI的串行ADC接口的设计 SPI(SerialPeripheralInterface---串行外设接口)总线系统是一种同步串行外设接口,允许MCU与各种外围设备以串行方式进行通信、数据交换,广泛应用于各种工业控制领域。 MAX187用采样/保持电路和逐位比较寄存器将输入的模拟信号转换为12位的数字信号,其采样/保持电路不需要外接电容。MAX187有2种操作模式:正常模式和休眠模式,将置为低电平进入休眠模式,这时的电流消耗降到10μA以下。置为高电平或悬空进入正常操作模式。
ADC
- 电位器的模拟电压经过单片机的转换显示液晶上-Potentiometer s analogue voltage by AD transformation of MCU display on LCD
STCApplication
- sTC系列单片机内部AD的应用 STC89LE52AD、54AD、58AD、516AD这几款89系列的STC单片机内部自带有8路8位的AD转换器,分布在P1口的8位上,当时钟在40MHz以下时,每17个机器周期可完成一次AD转换。 -STC series single-chip internal AD Application STC89LE52AD, 54AD, 58AD, 516AD that several 89 series of STC has its own single-ch
ADConvert
- 基于ARM7的S3C44B0的ADC转换程序,驱动程序例程-ARM7 S3C44B0 ADConvert
ADC0804
- C51源程序,开发adc转换的基础入门知识-C51 source, development of basic entry-adc conversion of knowledge
C51
- 花钱购买的C51学习板里的源码,包括电路图,源码和hex文件,参照图纸接线后,直接烧录可运行。 内容齐全,包括键盘,数码管,温度显示芯片,LCD,ADC数模转换,时钟显示芯片,连接电脑键盘,与电脑通信,蜂鸣器,红外遥控等。。。单片机入门好资料-To spend money to buy the C51 source in the study board, including schematics, source code and hex file, in the light of wirin
ADC
- 基于c8051f020的单片机的数模转换,将单片机内部的温度传感器信号转换为数字信号-C8051F020 microcontroller-based digital-to-analog conversion, the internal single-chip temperature sensor signal is converted to digital signal
DigitalVoltageMeter
- 这是一个用MSP430单片机设计的基于FYD12864LCD的数字电压表的C程序。系统主要实现对电压的测量。其中,ADC采用MSP430149单片机内部自带的12位AD转换器。输入信号的最大值为+2.5V,你也可以选择其他参考源,使输入信号最大可达+3.3V。-This is a single-chip design using MSP430-based digital voltage meter FYD12864LCD the C program. System is mainly to ac
demo_10_3
- 用ATMEGA16实现一个简单电压表.采用动态扫描方式构成电压表的输出显示.ADC的参考电压源采用内部AVCC,转换后的结果换算成测量的电压值在4位LED上显示.-ATMEGA16 implementation using a simple voltage meter. Constitute the use of dynamic scanning of the output voltage meter display. ADC using the internal reference volta
adc_test
- 在msp430f149环境下,用iar编译,实现ADC转换-At msp430f149 environment, iar compiler used to achieve ADC conversion