搜索资源列表
fet140_tb_09
- MSP-FET430P140 Demo - Timer_B, PWM TB1-2, Up/Down Mode, DCO SMCLK-MSP-FET430P140 Demo-Timer_B, PWM TB1-2. Up / Down Mode, the making of SMCLK
msp430x1xx_fet_1
- //*** *** *** *** *** *** *** // MSP430x1xx Demo - Software Toggle P1.0 // // Descr iption Toggle P1.0 by xor ing P1.0 inside of a software loop. // ACLK = n/a, MCLK = SMCLK = default DCO // // MSP430x1xx // ----------------- // /|\\
fet110_1
- //*** *** *** *** *** *** *** * // MSP-FET430x110 Demo - Software Toggle P1.0 // // Descr iption: Toggle P1.0 by xor ing P1.0 inside of a software loop. // ACLK = n/a, MCLK = SMCLK = default DCO ~800k // // MSP430F1121 // --------------
msp430x11x1_ta_uart9600_04
- Descr iption: This program demonstrates a half-duplex 9600-baud UART using // Timer_A3 using no XTAL and an external resistor for DCO ROSC. DCO used for // TACLK UART baud generation. The program will wait in LPM4, echoing back // a received ch
fet410_ta
- MSP-FET430P410 Demo - Timer_A Toggle P5.1, CCR0 Contmode ISR, DCO SMCLK Descr iption Toggle P5.1 using using software and TA_0 ISR. Toggle rate is set at 50000 DCO/SMCLK cycles. Default DCO frequency used for TACLK. Durring the TA_0 ISR P5
d169_dma
- D169 Demo - DMA0 Repeated Burst to-from RAM, Software Trigger Descr iption A 32 byte block from 220h-240h is transfered to 240h-260h using DMA0 in a burst block using software DMAREQ trigger. After each transfer, source, destination and DMA
fet140_spi
- MSP-FET430P140 Demo - USART0, SPI Interface to HC165/164 Shift Registers Descr iption: Demonstrate USART0 in two-way SPI mode. Data are read from an HC165, and same data written back to the HC164. ACLK = n/a MCLK = SMCLK = default DCO = UCLK
Using_the_DCO_Library
- ti发布的MSP430 dco库 使用非常方便,非常稳定
fet440_uart11_38400
- Echo a received character, RX ISR used. Normal mode is LPM0. // USART1 RX interrupt triggers TX Echo. // Baud rate divider with 1048576hz = 1048576/38400 = ~27.31 (01Bh|03h) // ACLK = LFXT1 = 32768Hz, MCLK = SMCLK = default DCO = 32 x ACLK = 10
msp430f26xx示例程序
- TI公司单片机MSP430f261x系列单片机的官方实例程序
fet110_ta_uart9600_04
- 利用MSP430单片机生成PWM波,并从P2.6脚输出。-MSP-FET430x110 Demo- Comp_A Output Comparator_A reference voltages on P2.Descr iption Output comparator_A reference levels on P2.3. Program will cycle through the on-chip comparator_A reference voltages with output o
dpll
- 基于Verilog的数字锁相环。包括三个模块,数字鉴相器DPD、数字环路滤波器DLF、数控振荡器 DCO三部分构成-Verilog-based digital PLL. Consists of three modules, the digital phase detector DPD, digital loop filter DLF, digitally controlled oscillator DCO three parts
USBfunctions
- msp430单片机的USB的控制程序,源代码,c语言写的。- MSP-FET430P140 Demo- Timer_A, Toggle P3.4, Overflow ISR, DCO SMCLK
LABD2
- Developed for use with MSP430x22x4 MCU (2274). Made with Code Composer Essentials v3.1. VLOCLK used, MCLK from VLOCLK.Also calibrated DCO s used. Basically this file is for educational use working with Basic Clock Module+. Timer interrupts used fo
LPM3
- msp430进入LMP3休眠模式,每4秒点亮LED灯-his program operates MSP430 normally in LPM3, pulsing P3.4 at 4 second intervals. WDT ISR used to wake-up system. All I/O configured as low outputs to eliminate floating inputs. Current consumption does increase wh
msp430x42x0_clks_01
- msp430f4270 时钟测试程序 SP430x42x0 Demo - FLL+, Output MCLK, ACLK Using 32kHz XTAL and DCO-msp430x42x0_clks_01 SP430x42x0 Demo- FLL+, Output MCLK, ACLK Using 32kHz XTAL and DCO
msp430x42x0_dac_01
- MSP430x42x0 Demo - DAC0 1V output Descr iption: Output 1V on DAC0 ACLK = n/a, MCLK = SMCLK = default DCO-MSP430x42x0 Demo- DAC0 1V output ACLK = n/a, MCLK = SMCLK = default DCO
msp430x42x0_fll_01
- MSP430x42x0 Demo - FLL+, Runs Internal DCO at 2.45MHz -MSP430x42x0 Demo- FLL+, Runs Internal DCO at 2.45MHz
msp430x42x0_ta_01
- MSP430x42x0 Demo - Timer_A, Toggle P1.0, CCR0 Cont. Mode ISR, DCO SMCLK- MSP430x42x0 Demo- Timer_A, Toggle P1.0, CCR0 Cont. Mode ISR, DCO SMCLK
msp430F135LED
- msp430F135LED动态显示,在8位数码管显示模块)动态扫描显示4321,时钟ACLK= n/a, MCLK= SMCLK= default DCO ~ 800k-msp430F135LED dynamic display, the 8-bit digital display module) dynamic scan showed 4321, the clock ACLK = n/a, MCLK = SMCLK = default DCO ~ 800k