搜索资源列表
AnteeoBee_20060218
- his project was built and tested with WinAVR-20060125. Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!! To build the code, just install WinAVR and run \"make\" from the console in echomaster and ech
fpgaandmcuand25h20.rar
- FPGA 和ＭＣＵ的并口通信 及ＭＣＵ和Ｅ２ＰＲＯＭ(FM25H20)SPI通信 功能：ＦＰＧＡ对ＭＣＵ的写（ＦＰＧＡ发给ＭＣＵ的地址是写进Ｅ２ＰＲＯＭ的地址 ，Ｅ２ＰＲＯＭ中的数据是 ＦＰＧＡ发送的数据。） ＦＰＧＡ对ＭＣＵ的读（ＦＰＧＡ读取它发给ＭＣＵ在Ｅ２ＰＲＯＭ中存取的数据） 程序和图见附件 恳请高手指导 小弟急啊！,FPGA and MCU
SPI-Driver-For-WinCE-S3C2410.r
- 本驱动程序是基于WinCE系统的s3c2410的SPI驱动源码,The driver is based on the WinCE system s3c2410 the SPI driver source
spi_V1.0.3
- //说 明：msp430通过模拟的spi驱动flash W25X32 //描 述：用于主函数中直接调用 flash写函数 写入数据 //功 能：写入flash 一个字节数据 flash地址自动加一 //端 口：p7.0 接/CS片选端 , p7.1用于时序脉冲, p7.2 用作MOSI主机输出从机输入 ， // p7.3用作MISO主机输入从机输出, // p1.4接/WP写保护引脚 ，此程序里没有用到 所以直接拉高，不用。 // 也可以连写 都试过了
SAM7X256E
- AT91SAM7X256应用资料,包括TEI\SPI\RTC等例程-AT91SAM7X256 application information, including TEI \ SPI \ RTC and other routine
SST25VF016B-SPI
- STM32 读写FALSH- STM32 R/W FALSH
spi
- SPI总线接口的verilog源码，包含仿真模块modelsim 和 quartus 工程。本人测试通过。-SPI bus interface in verilog source code, including the simulation module modelsim and quartus project. I test.
SCA100
- 51单片机SPI读取SCA100角度值,带温度补偿,精度达到0.008度.-51 Single-chip SPI read SCA100 angle values, with temperature compensation, accuracy of 0.008 degrees.
FREQSYN
- 使用Verilog语言编写的使用SPI总线设置频率LM2346,可通过设置其R寄存器对其输出频率进行设置（需相应的射频电路相配合）。-The use of Verilog language use SPI bus frequency settings LM2346, can be by setting up its R register set of its output frequency (to be matched by corresponding RF circuitry).
spi_burst
- Verilog block SPI for Burst R/W Operation
sdopration
- SPI模式下，，，，，，，，SD卡的读写-W/R SD card
spi_slave
- spi slave 8bit address 1bit r/w 7bit number data
71477212SAM7X256-SPI
- IAR 3.01a IDE编译环境下的SPI读写MAX96XX存储芯片程序-SPI r/w MAX96XX flash ,development in IAR4.03 ide
auto_w_r_spi
- 能够自动读写SPI ROM的控制器，读写的资料直接放到fifo中，经过实际的班子验证，很好用。-Can automatically read and write SPI ROM controller, read and write data directly into fifo, after the actual verification team, very good use.
SDHC
- MSP430F169与SDHC卡的通信程序，支持IO和SPI方式-communication program between SDHC card and MSP430F169.And it is in support of IO as well as SPI mode
SPIFlash
- DOS下通过南桥SPI Controller读写BIOS flash信息的example code，汇编代码-DOS, read and write BIOS flash information through the South Bridge SPI Controller, example in assembly code
spi25
- 铁电SPI 读写 FPG 外挂SPI铁电存储器的读写控制代码.-FM25** SPI R/W
K60PucosiiP28J60ParpPicmp
- K60上移植ucosii，使用spi读写28J60，调试arp，icmp协议-K60 transplant ucosii, using spi r/w 28J60, debugging arp, icmp protocol
spi-slave-mode
- bjx 301a spi 从模式读写数据，-bjx 301a spi slave mode for r/w data
stm8PCC1101-R
- STM8通过SPI总线驱动CC1101，接收端源码。-STM8 via SPI bus driver CC1101, the sender source.