搜索资源列表
STM32.RAR
- STM32所有开发例子程序.RAR GPIO_out 8个led闪烁 注意：接跳线D1_CS, D2_CS, LCD 液晶上显示英文字符 LCD_汉字 液晶上显示汉字 LCDBMP 液晶上显示图片 ADC 液晶上显示采的电压值 SDcard SD卡上建立一个文件 UART 串口发送字符在液晶上显示 RTC 液晶上显示时间 ExIRQ 外部中断,S2给中断信号 Timer 定时 CAN CAN总线-STM32 ex
Micrium-ST-uCOS-II-LCD-STM32
- uCosII2.86在STM32F10BLK1开发板上的移植例程，已完成Flash、LCD、SD、ADC驱动部分的开发，内含完整的BSP-uCosII2.86 board in the development of transplant STM32F10BLK1 routines have been completed Flash, LCD, SD, ADC-driven part of the development, the BSP includes a complete
STM32ADC
- 用STM32单片机控制内部12位DAC进行电压采集，使得采集电压显示在LCD1602上-STM32 MCU with internal 12-bit DAC to control the voltage acquisition, making the acquisition on the voltage displayed on the LCD1602
stm32-ADC-0--100V-0.08vError
- stm32 arm单片机基于KEIL编译环境，开发的一款高精度ADC采样程序代码，采样电压0--100v和0--20v两路，最大误差精度0.08v。通过2.8寸lcd显示在液晶触摸屏幕上-STM32 arm microcontroller based KEIL compiler environment, the development of a high-precision ADC sample code, the sampled voltage- 100v and 0- 20V two-way
stm32-PWM-output-waveform-display
- stm32 ARM单片机的PWM输出，然后通过通过ADC采样，并且在2.8寸液晶触摸屏幕上显示PWM动态的电压点位和ADC值，pwm频率和占空比可以通过改变定时器值而调整-STM32 ARM microcontroller PWM output, and then passed through the ADC sampling, and dynamic voltage point of the PWM and ADC values 椠渀 the 2.8-inch LCD touch screen
stm32-ADC
- 通过ADC1读取通道1（PA1）上面的电压（对应多功能端口的ADC），在LCD模块上面显示ADC转换值以及换算成电压后的电压值。-ADC converted value is displayed at the LCD module and converted into a voltage, the voltage value read by the ADC1 channel 1 (PA1) at the voltage (corresponding to the multi-purpose po
STM32adc-uart--tim-and-lcd
- 此工程基于Keil平台，实现了STM32的ADC功能，TIM定时中断等其它功能，并且在原来的基础上优化了lcd12864的显示，图形显示更加稳定，快速，本人亲测，如有不好的地方请多多包含。-This project based on Keil platform to achieve the STM32 ADC functions, TIM timer interrupt, and other functions, and on the basis of the original optimize
STM32-LCD12864-menu
- STM32控制液晶12864显示开机画面，多级菜单，配置ADC,DAC,DDS.-STM32 12864 LCD display boot screen control, multi-level menu, configure ADC, DAC, DDS.
ADC-shiyan
- 本实验将实现如下功能：通过ADC1读取通道1（PA1）上面的电压（对应多功能端口的ADC），在LCD模块上面显示ADC转换值以及换算成电压后的电压值。 注意：本实验的参考电压是3.3V，如果你想用其他的参考电压，可以通过战舰STM32开发板的P7端口设置。注意设置好其他参考电压以后，输入电压不要超过参考电压的最大值-This experiment will achieve the following function: ADC1 read channel 1 (PA1) at the
stm32-temperature-measurement
- 打开stm32的内部adc温度检测通道，通过stm32内部的温度检测元件检测cpu的温度， 并通过28寸LCD彩屏将温度显示出来。-Open stm32 internal adc temperature detection channel, cpu temperature detected by the temperature detection stm32 internal components and 28-inch LCD color screen by the temperature
STM32-ADC
- STM32_ADC利用通道11来采集模拟电压，可以在液晶屏上显示出来。-STM32_ADC use channel 11 to acquire the analog voltage can be displayed on the LCD screen.
STM32-ADC
- STM32F103模数转换程序,一路ADC的采样,并在LCD上显示采样值。-STM32F103 ADC programms, a channel ADC sampling, and displayed sampling values on the LCD.
STM32-ADC-V2_2
- manejo y configuracion de modulo LCD stm32
ADC显示(自带固件库)
- 调试lcd显示程序,基于stm32 151系列的与液晶屏相连的程序，大家可以在此基础进行学习(Debugging LCD display program, based on the STM32 151 series connected with the LCD screen program, we can learn on this basis)
实验25：LCD-ADC
- PZ6806L硬件平台的ADC程序，使用LCD显示(the project is a ADC test of STM32,it is useful of PZ6806L hardware,)
ADC实验
- STM32控制程序，其作用是将ADC采样的电压值显示在LCD屏上。(STM32 control program, the role is to ADC sampling voltage value displayed on the LCD screen.)
ADC测试
- ADC的操作，采集电压并通过lcd显示出相应的值(ADC operation, collecting voltage and display through LCD)
实验29：LCD-ADC-DMA
- 使用STM32F103 功能：TFT彩屏显示 ADC转换结果 ADC单通道连续转换(Use the STM32F103 function: TFT color display ADC conversion results ADC single channel continuous conversion)
ADC
- 学习STM32内部ADC的使用，通过STM32内部ADC1读取通道1（PA1）上面的电压，在LCD模块上面显示ADC转换值以及换算成电压后的电压值。(Learn the use of ADC in STM32, read the voltage above the channel 1 (PA1) through STM32 internal ADC1, display ADC conversion value on LCD module, and convert the voltage valu
mini简易示波器 ADC+DMA
- 基于正点原子mini板的简易示波器 ADC+DMA+LCD(Embadded Oscilloscope STM32F203RCT6)