搜索资源列表
annnn
- Capacitor bank placement in distributed generator
LTC6903
- 1kHz 至 68MHz 串行端口可设置振荡器-The LTC® 6903/LTC6904 are low power self contained digital frequency sources providing a precision frequency 1kHz to 68MHz, set through a serial port. The LTC6903/LTC6904 require no external components other than a power
MATHCADjulibaohu
- 应用于电力系统距离保护中过渡电阻对差动电流保护的影响，通过对电容补偿的整定进而分析结果。-The protection applies to the transition resistance on differential current protection, through the tuning capacitor compensation and then analyze the results the power system.
KONGZAIHEZHAI
- 在距离保护中，能正确的判断含有电容补偿和不含电容补偿作用下，距离保护动作的特性。-In the distance protection, the judge correctly contain lower capacitance compensation and non-compensation capacitor, the distance protection operation characteristics.
000545
- 此文件为原论文，八十多页。请用CAJ客户端观看。回路电阻是反映电力开关设备性能和运行状态的一项重要技术指标。 为了实现对断路器回路电阻的快速准确测试,设计了一种基于超级电容大电流放电特性的回路电阻测试系统-This file as the original papers and more than 80 pages. Please use CAJ client to watch. Loop resistance is an important technical index to reflect
power_active_filter
- The circuit models a standard shunt AHF with IGBT inverter and series inductor on the AC side and DC capacitor energization. The load consists of two diode rectifiers which are phase-shifted by 30 degrees. The Delta-Y connected rectifier is connected
bct3288
- BCT3288A是一颗使用SPI协议控制的16通道恒流 驱动芯片，每个通道最大输出电流能力 40mA， 每个通道有64个等级电流可独立控制。 BCT3288A外围电路简单，只需一颗电阻设置每 个通道的最大输出电流，以及一颗滤波电容， 使用MCU的三个 GPIO口，可非常方便的实现芯 片的开启、炫彩控制、关断功能。-BCT3288A is using a 16-channel constant current SPI protocol control D
stm32f1test
- ADD：这个模块我在调试过程中发现很容易便会死机，对干扰跟电源扰动比较敏感，过段时间试试加个电容减少下波纹。SI4463具有RSSI功能，与WIFI一样可以通过这个来估计距离，不太清楚其信道评测功能，将继续研究以便实现自动跳频-ADD: this module I found in the debugging process easily will crash, disturbance is more sensitive to power, the interference over time
capacitor-bank
- In this work commercial software, OrCAD PSpice is used to build three-phase equivalent models of the sample distribution system with two radial primary feeders, and investigate the unbalanced operation conditions of two sample feeders before
AC-Down
- 电容降压阻容计算含具体算法和选型电容降压原理图和设计图-Capacitor step-down resistor-capacitor containing specific algorithm to calculate and selection
cap
- 本代码是基于STC89C52单片机最小系统开发环境的测量未知电容电路。根据555定时器的不同电容充放电时间得到未知电容值。-The code is based on the STC89C52 MCU minimum system development environment for the measurement of unknown capacitance circuit. According to the different capacitor charge and discharge t
gui_dyn_14_3
- 动态电路分析，用户输入电阻、电容、电容初始电压。-Dynamic Circuits, user input resistance, capacitance, initial voltage of the capacitor.
power-circuit
- 在电源输入的前端利用旁路去耦电容滤波器，在+12V输入时，首先通过一个电解电容C1和电容C2保证电压的输入稳定，之后选择利用稳压器NCP1117ST50T3G将输出电压降到+5V，如图3.5所示，其输出电流为1A。在稳压器之后继续采用一个电解电容C3来保证输入到芯片的供电电压稳定。-Power input at the front end of the use of bypass decoupling capacitor filter when+12V input through a first
25fb_drv_doublebuffer
- 开发板4412_ARM9开发，通过framebuffer控制电容屏，设置部分驱动方法：* 需要先关闭内核中的framebuffer驱动，否则会冲突 make menuconfig -> Device Drivers -> Graphics support -> Samsung S3C framebuffer support 同时要确保CONFIG_FB_S3C_NR_BUFFERS生成 程序里面有详细注释，中文注释-Development board 4412_
danpianji
- 1.晶振，至于大小由你单片机时钟周期要求而决定（用于计时，与两个电容并联使用，电容大小由你的晶振决定，一般用22pF） 2.复位电路（用于复位） 3.电源（用于供电，一般用电脑的USB口供电） 4.烧制程序的口（可用串口配合MAX232配合使用，也可以做个并口输入，这个要根据你使用单片机的种类决定，比如ATC可用并口，STC一般只用串口输入等等）-Crystal, as the size of your microcontroller clock cycle requirements
guangfude1buck_boost
- 根据光伏电池的特性，利用超级电容特点设计升降压电路-According to the characteristics of photovoltaic cells, using the characteristics of super capacitor design lifting voltage circuit
china_sh0015
- 无线充电电动牙刷软件源码，瑞萨R7系列主控，升压型开关电容转换器FST18-Wireless charging electric toothbrush software source code, Renesas R7 series main control, boost switched capacitor converter FST1822
SC_boost_converter11111
- 超级大电容以及电池的充放电仿真，根据功率控制从而得到给定的输出功率-Super capacitor and battery charge and discharge simulation, according to power control to get a given output power
parallel_battery_SC_boost_converter
- 简易的蓄电池与超级电容混合储能系统。可以观测SOC值变换，电压电流变化等-A simple battery and super capacitor hybrid energy storage system, can achieve SOC monitoring, voltage and current monitoring, contrast.
STC触摸开关C
- 基于STC触摸开关C的相关开发程序，ADC对电容式电压采集(Based on STC touch switch C related development procedures, ADC capacitor voltage acquisition sequence)