搜索资源列表
linux-HDDTest
- linux下查看硬盘坏道信息代码 对于硬盘的坏道的确没有什么好的办法,ata协议中的smart命令本意上是好的,但是很多的硬盘厂商并没有很好的实现smart的功能;硬盘的相关错误信息会存在相应的扇区里,但是这些扇区相当于一个环形的缓冲区,所以记录的错误信息有限,如果需要完整的硬盘坏道信息,smart就无能为力了。通过完整的读一遍硬盘可以找出坏道的完整信息,但是读牵涉到了DMA的数据传输过程所以效率较低;ata的协议里READ VERIFY (EXT)命令大大提高效率,该命令是NO DA
Design_DMA
- 基于PCI的DMA接口设计,验证后实现了PCI的数据传输功能。-Based on the DMA PCI interface design, after the implementation of the PCI data transfer function.
adccc
- AD转换,双通道stm32,采用DMA方式传输-ADC transfer
dma_ram_to_ram
- DSP 28335 基于ccs4.2 的DMA RAM传输程序-DSP 28335 based on CCS4.2 DMA RAM to RAM
w25q64
- stm32f4代码之w25q64驱动,spi普通读写及spi dma读写。spi普通读采用寄存器操作方式以及nop延时能够达到最大传输速率。-w25q64 stm32f4 code for the driver, spi and spi dma ordinary reader to read and write. spi register using ordinary read operation and nop delay to reach the maximum transfer rate.
rvmdk
- 此代码将SPI_DMA的传输功能做成了库的形式,已验证完成,可以方便使用者的移植-This code SPI DMA transfer function of the form of libraries made, verified complete, the user can easily transplant
qpecutivedefinition
- WINDOWS环境下,DMA数据传输驱动程序源代码,不错的-WINDOWS environment, the DMA driver source code, data transmission
snvironmdytenvironmentdriver
- WINDOWS环境下,DMA数据传输驱动程序源代码,不错的(WINDOWS environment, the DMA driver source code, data transmission)
STM32F407_AD_DMA_TFT
- 通过STM32F407内置的12位adc对外部的模拟信号进行采集,利用DMA进行数据传输以提高CPU的使用效率,最后将ADC采集到的数据显示在3.4寸的液晶触摸屏上。(Through the 12 bit STM32F407 built-in ADC external analog signal acquisition, using DMA data transmission, in order to improve the use efficiency of CPU, and finally
0224897
- WINDOWS环境下,DMA数据传输驱动程序源代码,不错的(WINDOWS environment, the DMA driver source code, data transmission)
SPI
- 基于5880主控制器的spi驱动程序,有polling、INT、DMA三种传输方式实现数据的传输(SPI driver based on 5880 master controller, polling, INT, DMA, three transmission methods to achieve data transmission)
DAC
- 这个例子描述了如何使用DMA将数据传输到DAC外围设备。(This example describes how to use DMA to transfer data to DAC peripheral)
CV_FPGA_to_HPS_Bridge_Design_Example
- FPGA通过AXI总线传输数据给ARM,ARM使用DMA方式接收数据!(FPGA to ARM Bridge design example)
AXI-HP-ZYNQ
- 用Vivado IPI搭建的Zynq-7000 PS到PL通信过程,使用了AXI-HP接口,利用AXI-DMA IP实现直接读写DDR的过程,软件可以配置传输尺寸。(The Zynq-7000 PS to PL communication process is built by Vivado IPI. AXI-HP interface is used, and AXI-DMA IP is used to read and write DDR directly. The software can
DMA_xintf_to_ram
- DSP28335 应用例程【片外SARAM到RAM】DMA数据传输实验教程(example for DSP28335 DMA_xintf_to_ram)
Si4432无线数传STM32程序
- Si4432无线数传STM32程序 1. 采用串口1与外部进行通信,可传输接收任意长度数据; 2. 将接收后的数据无条件发送给指定地址的si4422模块; 3. 接收模块收到数据后无条件的将有效数据通过串口1的DMA传出;即:基于SI4432的点对点串口透传模块