搜索资源列表
DSP_TEST
- TI DSP 实验测试程序,很全面。1指令实验,2存储器,3串行口等。-TI DSP experimental testing procedures very comprehensive. A directive experiment, two memory, serial port, etc. 3.
yibu
- DSP芯片TMS320F206异步串行口的应用-DSP TMS320F206 Asynchronous Serial Interface Application
MotorControl_final_version
- 一个应用于LF2407的风扇转速控制系统,基于北京精仪达盛科技公司的试验箱,主要实现了风扇转速PID控制算法以及和利用DSP的串行口与上位机通讯的功能,以及LED,LCD显示,具体的通讯协议在压缩包里面的doc里面有
vortex-datasend
- DSP异步串行口SCI的数据发送和接收程序,通过验证。-DSP asynchronous serial port SCI sending and receiving data process through verification.
sci_demo
- 使用TMS320F2812的SCI串行口与计算机进行通讯的程序。使用TI提供的C/C++头文件与公用文件,可在TI网站上下载。-a demo illustrates the method of DSP-PC communicating using Sci of DSP and RS232 of PC.
RS232ADIBF533
- 本程序为调试ADI BF533DSP串行口通讯功能的小程序,非常适合刚入门的同学学习。-This C source code is suitable for a new DSP programmer to begin his UART testing at BF533 EZ-kit
3serialportcommunicationsource
- 3串行口通讯源码,主要应用与DSP与CPLD,上位机等通讯交互-3 serial port communication source, the main application and DSP and CPLD, interactive communications, such as PC
shiyanceshi
- 一些DSP试验测试程序,存储器,指令试验,串行口,步进电机及硬件中断等-Test procedures for a number of DSP, memory, command pilot, serial port, stepper motors and hardware interruption
SPI_STM32_FPGA
- STM32F1与FPGA通过SPI进行通信,我上传的是32部分的程序,已经通过串口测试成功。此程序可拓展为和单片机,DSP通过SPI进行通信-STM32F1 and FPGA communication through the SPI, I uploaded the 32 part of the procedure has been successfully tested through the serial port. This program can be extended to and s
flashloader_28x
- 基于labwindowsCVI编写的TMS320F28xx的DSP在线升级上位机程序,通过串口实现,并附带串口协议。上位机软件支持使用CCS编译的.out目标文件并自动进行格式转换。 新建cvi工程。将所有文件添加进工程编译即可。-Upgrade based labwindowsCVI prepared TMS320F28xx of DSP Online PC program, through the serial port, and comes with serial protocol.
TMS320F28x_boot
- TMS320F28xx系列的DSP在线升级boot程序,通过串口实现和上位机软件的通信并实现软件在线升级,boot程序分配在Flash的sectorA区,应用程序分配在其他区。 新建CCS工程并将几个文件夹加入编译即可。-TMS320F28xx Series DSP Online Upgrade boot program, and communication through the serial port of the PC software and implementing softwar
luna_V1.2
- DSP1701 控制,aux, i2s 输入 i2s 输出。 串口命令切换音源 。 -it is to control 1701 DSP 。 input aux and i2s , output , i2s 。
REPORT3
- ADI dsp信号处理仿真实验,片内外设及应用 1. 了解DSP外部存储器SDRAM的初始化方法; 2. 掌握DMA控制器的使用方法; 3. 掌握串口的使用方法; 4. 掌握SPI端口的使用方法; 5. 掌握外部标志位(FLAG4-9)的使用方法; 6. 掌握外部中断(/IRQ0~2)的使用方法。 -ADI dsp experiment 3
uart
- 基于FPGA的RS232串口通信程序。可以和MCU的单片机,还有DSP,以及上位机通信 -FPGA- based RS232 serial communication program.And MCU can be single-chip, as well as DSP, and the host computer communication
DSP280x_Gpio
- DSP实现AD采样与串口通信中GPIO口的分配-DSP Practice AD Adoption Kushiguchi Communication in progress GPIO mouth distribution
SCI_RS232andRS485
- dsp通过scic与计算机串口进行485通信(DSP communicate with through computer serial port through SCIC)
Simulink_DSP28335_SCI_TEST
- 通过在simulink搭建串口通信模型实现和DSP硬件平台的数据传输(Through the establishment of serial communication model in Simulink and the data transmission of DSP hardware platform)
RDA5807M
- DSP FM收音机,按键和蓝牙串口控制,自动搜台或者手动输入频率,MCU:STC12C5A60S2,晶振:11.0592M。(DSP FM radio, buttons and Bluetooth serial control, automatic search table or manual input frequency, MCU:STC12C5A60S2, crystal oscillator: 11.0592M.)
CANBurn
- TI DSP F28035芯片烧录程序,利用串口网线烧录程序,解决了购买仿真器刷程序的烦恼,(TI DSP F28035 chip burning program, using serial network wire burning program, to solve the trouble of buying the simulator brush program.)
Example_2833x
- TI DSP 28335 平台;gps.c主是NMEA0183协议,将字符串转化为经纬度等数据,存入结构体;convertGeoToUTM.c将经纬度换算为UTM坐标;Example_2833x.c是主函数,不能直接运行,项目中其它代码都删掉了,仅保留了串口中断服务函数。(The TI DSP 28335 platform; gps.c is the main NMEA0183 protocol, string into latitude and longitude data structure