搜索资源列表
cpu_timer
- DSP程序，TMS320F2812芯片CPU定时器例程，定时产生中断-DSP program, TMS320F2812 chip CPU timer routine, timer interrupt is generated
Audio-watermarking-internship-report
- 音频信号的水印设计，以音频信号为载体，将秘密信号嵌入载体音频信号当中， 实现音频信号的水印。采用变换域小波变换（DWT）的技术，将音频信号进行小波变换，提取出低频分量，然后将水印嵌入到音频信号的低频当中。实验当中先在MATLAB 上面进行了仿真实验，并且通过加入噪声以及滤波等进行干扰以此检测了算法的透明性和健壮性，然后利用C 语言进行了测试，最后经 过一些修改，例如加入定时器以及进行中断的处理和加入缓冲在DSP 板子上实现了加入水印的音频声音的播放。-Audio signal water
AD02
- 使用TI公司的DSP芯片TMS320F2812的定时器中断事件的方法启动ADC模块，设定ADC采样-Use TI' s DSP chip TMS320F2812 timer interrupt event starts ADC module, set the ADC sampling
DM642_Timer
- ti dsp dm642 timer时间例程，This example uses a timer to read and write the ESAM.-ti dsp dm642 timer time routines This example uses a timer to read and write the ESAM.
6455Timer_example
- C语言编写的DSP例程,是一个定时器程序 希望对初学者有用-The DSP routines written in C, a timer program useful for beginners
BF53
- 主要针对于ADSPBF53X 系列dsp学习的例程，其中包括SDRAM,GPIO,EBIU,UART,TIMER,FLASH等程序-For ADSPBF53X series dsp learning routines, including SDRAM, GPIO, EBIU, UART, TIMER, FLASH program
lab3-TIMER0
- DSP数字信号处理中有3个定时器，分别为定时器0，定时器1，定时器2.本程序实现对定时器0的配置。-DSP digital signal processing has three timers, Timer 0, Timer 1, Timer 2 Timer 0 for the program' s configuration.
lab4-TIMER1
- DSP数字信号处理拥有丰富的硬件资源能够实现各种复杂的运算和控制，其中定时器1的配置和应用较为重要，本程序介绍了定时器1的配置与应用。-DSP digital signal processing has abundant hardware resources to achieve a variety of complex operations and control, in which the configuration and application of Timer 1 is more im
lab5-TIMER2
- DSP数字信号处理中定时器2一般是留给调试用的，也可以作为通用定时器使用，本文件介绍了定时器2 的配置与使用。-DSP digital signal processing timer 2 is generally reserved for debugging purposes, can also be used as general-purpose timers, this document describes the configuration and use of timer 2.
lab4_timer
- dsp中定时器中断实验，c语言编译,CCS软件开发-dsp the timer interrupt experiments, c language compiler, CCS Software Development
F2808_TIMER
- 利用DSP,F2808的定时器功能，将GPIO19管脚每隔一秒开关一次，将GPIO19连接的二极管点亮熄灭一次-Timer function, using DSP, F2808 will GPIO19 pin once every two seconds to switch, connect the GPIO19 diode light goes out
sy2
- DSP实验二，C和ASSEMBLY的混合编程。 掌握中断矢量表的使用，掌握定时器中断的使用方法，学习CCS中图形观察动态数据的方式，学习用定时器实现数字振荡器的算法。-DSP experiment two, C and ASSEMBLY mixed programming. Mastered the use of the interrupt vector table, master timer interrupt to use, learn CCS dynamic data in graph
epwm_dma
- Ti DSP 28335 EPWM 示例，使用EPWM发出脉宽调制波形。基于定时中断。-Ti DSP 28335 EPWM example, the use of pulse width modulation waveform EPWM issue. Based on the timer interrupt.
eqep_freqcal
- Ti DSP 28335 QEP 检测转速程序，基于定时中断，通过单位时间的脉冲数计算转速。-Ti DSP 28335 QEP speed detection program, based on the timer interrupt, the number of pulses per unit time through the calculation speed.
watchdog
- Ti DSP 28335 程序，激活片上看门狗，基于定时中断清除触发看门狗。-Ti DSP 28335 program, activate the on-chip watchdog timer interrupt clear trigger based watchdog.
LED
- 基于DSP TMS320F2812的CPU定时器之LED实验-Based on DSP TMS320F2812 timer of the CPU LED test
EX02_CpuTimer0
- DSP经典入门例程，timer0定时器中断控制流水灯实验，F2812芯片，循环点亮和熄灭LED，时间间隔为1s。-DSP classic Tutorial，about how to enable timer 0 to control the led light and mute.
epwm_timer_interrupts
- dsp 28335 timer 例程 很好很很强大-dsp 28335 timer examples
DSP_AD_12864
- 由DSP事件管理器EVA的定时器T1启动AD转换，采样两路电压，AD转换后，液晶屏12864显示结果-DSP start AD conversion by the Event Manager timer T1,sample two voltages,AD conversion,Displays the results by 12864
3.2.4-cputimer
- DSP(TMS320F2812)系统定时器，主要通过定时器2实现两个LED的轮流亮灭状态。-DSP (TMS320F2812) system timer, Timer 2 is mainly realized through two LED light turns off state.