搜索资源列表
-
0下载:
真正实现了高级定时器和普通定时器的输入捕获,分别捕获一个脉冲,脉冲由51单片机产生,可自己调节精度-Truly advanced timer and timer input capture, respectively, to capture a pulse, the pulse generated by 51 single-chip, and can adjust
Section accuracy
-
-
0下载:
采用Atmaga128芯片,六位数码管,实现频率计,理论测试范围在125HZ--128kHZ,利用T1定时器输入捕捉法-By Atmaga128 chip, six digital tube, to achieve frequency meter, theory test range 125HZ- 128kHZ, using T1 timer input capture method
-
-
0下载:
S52三个定时器实现两路测速(测频)系统,一个定时器作时间基准,另外两个定时器作输入捕捉用,实现测频。-S52 3 Two Speed Timer (measuring frequency) system, a timer for a time basis, for the other two timers with input capture, to achieve frequency measurement.
-
-
0下载:
1、通过定时器1的输入捕获功能,测量脉冲宽度;
2、测量脉冲18HZ到1KHZ之间;
3、按下INT1,启动测量;按下INTO,停止测量;
4、测量值利用74LS164串行显示,精度±2HZ;
-1, by the timer 1 input capture, measure pulse width 2, between the measured pulse 18HZ to 1KHZ 3, press the INT1, start the measurement pres
-
-
0下载:
ECT定时器程序,用于单片机开发的程序,实现定时输入捕捉等功能。-ECT timer program, developed program for the microcontroller, to achieve timing input capture functions.
-
-
0下载:
用于MSP430F149。
定时器A捕获方波的信号周期。-For MSP430F149. Timer A capture cycle square wave signal. Signal input: P2.2
-
-
0下载:
STM32的通用定时器的输入捕获.利用通用定时器3的输入捕获功能对脉冲的捕获并且测量出周期和占空比-STM32 general timer input capture
-
-
0下载:
代码功能:在DSP2812平台上用C语言进行开发实现利用事件管理器EVA中捕获单元的捕获输入引脚检测两个事件变化的时间,即用捕获引脚CAP4检测手动按下开关的时间,至少五次,将两个捕获引脚每次变化是定时器的值存入数据区,手动开关计数值存入200H单元开始的数据区。-Code function: In DSP2812 platform using C language developed to use the Event Manager EVA capture unit to capture in
-
-
0下载:
STM32定时器的基本应用,PWM的的输入捕获,硬件调试通过,基本没有误差。
-The basic application of the STM32 timer, PWM input capture hardware debugging through, basically there is no error.
-
-
2下载:
STM32采用定时器管脚的输入捕获功能进行外部脉冲个数的采集,此代码仅采集脉冲个数,准确无误,用到的朋友下来看看,可检测编码器等PWM脉冲个数-STM32 timer pin input capture function for the acquisition of the external pulse number, this code is only collected the number of pulses, accurate, friend came down to see used
-
-
0下载:
基于MSP430的脉冲宽度检测代码程序,不用定时器A的输入捕捉功能,-MSP430-based pulse width detection code programs without Timer A input capture function,
-
-
2下载:
STM32入门篇之通用定时器彻底研究
TIMER-1:定时器上溢,中断中取反LED
TIMER-2:强置输出
TIMER-3:输出比较
TIMER-4:PWM输出
TIMER-7:单脉冲方式
TIMER-5:输入捕获模式
TIMER-6:PWM输入
TIMER-8: TIMER2作为TIMER3的分频器
TIMER-9:TIMER2来使能TIMER3
TIMER-10: IMER2启动TIMER3
TIMER-11: TIMER4的通道1同时出发TIM
-
-
0下载:
ATMEGA16的频率计主函数源代码,ICC的编译环境,利用了定时器1的输入捕捉功能-The ATMEGA16 a frequency meter main function source code, the ICC compiler environment, use of timer input capture function
-
-
0下载:
R8C/27 Group Timer RC(Input Capture)
-
-
0下载:
定时器4提供10ms的定时功能,作为系统节拍。
定时器1的1~4通道,定时器3的2通道,提供5个通道的PWM输出。
定时器3的1通道用作内部输入捕捉,校准最小时钟源。
定时器2为LIN提供时钟源(本模块不作处理)。-4 provide 10 ms timer timing function, as a system.
Timer timer 1 of 1 ~ 4 channel, 3 2 channel, provides five channels PWM output.
-
-
0下载:
PWM控制,输入捕捉码盘(相邻周期为0.05转),捕捉定时器1-PWM control input capture code disc (adjacent cycles of 0.05 rpm), Capture Timer 1
-
-
0下载:
MC9S08AW60的定时器1输入捕获驱动程序-MC9S08AW60 Timer 1 input capture driver
-
-
0下载:
TIM定时器输入捕捉程序,一个简单的收发程序-TIM timer input capture program, a simple program to send and receive
-
-
0下载:
通过stm32来控制超声波模块,并且通过TIM3定时器的输入捕获得出距离-Stm32 controlled by ultrasonic modules, and come from a timer input capture by TIM3
-
-
3下载:
STM32的TIM3通用定时器 输入捕获法测量频率 精确到1hz-STM32 of TIM3 general-purpose timer input capture accurate method to measure the frequency 1hz
-