搜索资源列表
keilMDK_jlink_debug_lpc2210_exflash
- KEIL下用JLINK调试LPC2210外部FLASH ,PDF文档及示例工程
KEIL_JLINK
- KEIL下用JLINK调试LPC2210外部FLASH的详细说明,注意对KEIL的设置,是PDF格式的
ee6604f3-f386-4fc1-a778-fca73e8e0481[1]
- keil 下jlink 调试lpc2210外部flash,网上当的,请各位大侠多指教-keil debugger jlink under lpc2210 external flash, the Internet, when the, heroes and more advice please
ADC
- LPC2148驱动ADC ----- A/D模数转换 这个工作区 每个工程包含3个配置选项 ISP_iFlash_Hex - 生成.Hex格式的目标文件 JLINK_iflash - 通过JLINK来烧写内部Flash的配置 JLINIX_iram - 通过JLINK来在内部RAM中调试 工程名: LCD ----- LCD(包含了中断) MMC ----- MMC卡读写 Uart ----- 串口通讯 USBMouse ----- USB
LCD
- LPC2148 drive LCD ----- A / D conversion module The work area Each project contains three configuration options ISP_iFlash_Hex - generated. Hex object file format JLINK_iflash - JLINK to the programming through the configuration of the intern
Uart
- LPC2148 drive LCD ----- A / D conversion module The work area Each project contains three configuration options ISP_iFlash_Hex - generated. Hex object file format JLINK_iflash - JLINK to the programming through the configuration of the intern
USBMouse
- LPC2148 drive LCD ----- A / D conversion module The work area Each project contains three configuration options ISP_iFlash_Hex - generated. Hex object file format JLINK_iflash - JLINK to the programming through the configuration of the intern
KElL
- Keil下用Jlink调试LPC2210外部FLASH的方法,验证可用-Keil LPC2210 under external FLASH with Jlink debugging methods, validation can be used
LED
- 1设计要求 PC6,PC7,PD6,PD13 LED快速交替闪烁。 2 硬件电路设计 在开发板上通用I/O口PC6,PC7,PD6,PD13作为控制D1,D2,D3,D4的控制线。 3软件程序设计 根据设计任务要求,软件程序主要包括: (1) 配置GPIO口,将PC6,PC7,PD6,PD13配置为上拉输出模式。 (2) 延时控制相应端口的置位和复位。 4 运行过程 (1) 使用Keil uVision3 通过
sdram_init_s3c6410
- 压缩包是使用JLink间接烧写s3c6410 nand_flash的源代码及可执行文件。由于s3c6410不像s3c2410那样有nor flash,可以方便的使用JTAG接口烧写引导程序。压缩包内的代码可以根据http://hi.baidu.com/__eabi/blog/item/5bfceaadf90eb39146106426.html帖子的说明,借助ADS1.2开发环境和JLINK,烧写二进制程序到开发板。 文件说明: sdram_init_s3c6410 | 、—
u-boot-1.1.6_OpenJTAG
- 使用JLink间接烧写S3C2410、S3C2440开发板Nor、Nand Flash源码在线!--The use of indirect JLink programmer S3C2410, S3C2440 development board Nor, Nand Flash source online!
[9]-I2C-EEPROM(Programming-whit-JLink-or-Flash-Ma
- lpc1768 i2c eeprom english example
Jlink_clone_solution
- 使用新版本的J-link驱动,版本在V4.50以后的,打开 J-Link ARM或者从KEIL MDK里面选择Debugger为J-LINK / J-Trace Cortex后点Setting时,会提示J-Link为Clone,然后自动关闭。 本文在网上搜集了许多解决办法,并且经过实践挑选出最为有效和完美的解决办法,整理成了一个教程。对于这些方法的原作者,表示感谢。 -A good tutorial to flash the not-working Jlink V8
JLink-p-Nor-P-Flash-
- 学习嵌入式Jlink烧写Nor Flash工程文件-Learning embedded in JLink programming Nor+ Flash project files
jlink-v8
- J-link驱动文件用于刷写固件可以用于损坏的Jlink上(固件丢失非硬件损坏)-J- link drive on file is used to flash the firmware can be used for the damaged Jlink (firmware loss than hardware damage)
注册机
- 编译器儿童问问他惹我让他问问人体我突然请问我确认去玩儿抢人头求侮辱他让他我天天(**JLink Warning: CPU could not be halted * JLink Info: Core did not halt after reset, trying to disable WDT. **JLink Warning: CPU did not halt after reset. **JLink Warning: CPU could not be halted **JLink W
Tiny_JLINK
- Jlink-0B建议调试工具,在j-flash 4.40版本下使用正常。文件包括有原理图和PCB图纸以及固件,可直接打样。(Jlink-0B recommends debugging tools to be used properly under version j-flash 4.40. Documents include schematics and PCB drawings and firmware, can be directly proofing.)
[7] RTC(Programming whit JLink or Flash Magic)
- [2] GPIO-Interrupt(Programming whit JLink or Flash Magic)
[8] ADC(Programming whit JLink or Flash Magic)
- ADC(Programming whit JLink or Flash Magic)
Setup_JLink_V500i
- JLink V5.00i版本驱动,支持Keil5。(Setup_JLink_V500i, J-Flash)