搜索资源列表
LED
- 1设计要求 PC6,PC7,PD6,PD13 LED快速交替闪烁。 2 硬件电路设计 在开发板上通用I/O口PC6,PC7,PD6,PD13作为控制D1,D2,D3,D4的控制线。 3软件程序设计 根据设计任务要求，软件程序主要包括： (1) 配置GPIO口，将PC6,PC7,PD6,PD13配置为上拉输出模式。 (2) 延时控制相应端口的置位和复位。 4 运行过程 (1) 使用Keil uVision3 通过
servo-motor-control
- 单片机控制伺服电机的正反转程序，伺服电机的控制仿真环境在keil环境中进行·-SCM control servo motor Reversible process, servo motor control simulation environment for the environment in keil
bujindianji
- 正反转可控制的步进电机，isis仿真和keil工程程序-Reversible control of the stepper motor, isis engineering process simulation and keil
lpc2104
- lpc2104流水灯仿真程序,用PROTEUS和keil联调-lpc2104 light water simulation program, with the PROTEUS and keil FBI
SHT11
- 基于proteus对SHT11的仿真。-SHT11-based simulation, C language code, the compiler environment KEIL, 51 chip!
calculator
- 一个简单的计算器，用51单片机做的，用到矩阵键盘，四位数码管。在keil下编译生成HEX文件，附上在proteus中的仿真文件。-A simple calculator, to do with the 51 single-chip, used in the matrix keyboard, four LEDs. In keil compiler generated HEX file, attached to the simulation in proteus file.
bujindianji
- 基于51单片机的步进电机控制程序源代码和proteus仿真源文件，采用keil做开发环境-Based on 51 single-chip stepper motor control program proteus simulation source code and source files, do the development environment using keil
DS1302-clock
- keil开发环境，stc89c52单片机与DS1302芯片做的一个实时时钟，工程文件齐全，并且有proteus的仿真效果图-keil development environment, stc89c52 microcontroller with a DS1302 real time clock chip to do the project documents are complete, and there proteus simulation renderings
Max7221-dynamic-display
- keil开发环境，stc89c52+Max7221控制数码管动态显示，工程文件齐全，并有proteus仿真效果图-keil development environment, stc89c52+ Max7221 control digital dynamic display, project documents are complete, and proteus simulation results Fig.
1.lpc2131-proteusPkeil
- 我自己试验成功的利用keil+proteus来仿真周立功深入浅出arm7点灯程序和仿真图，源码一个不差，可以下载便可以使用了-I have successfully tested the use keil+ proteus to simulate the lighting program arm7 ZLG layman and simulation diagram, a source not bad, you can download you can use the
xhfaqfangzhen
- 利用keil编写源程序，利用proteus仿真，能够正确显示仿真结果-Write source code using keil using proteus simulation, simulation results can be displayed properly
frequency_generator_v100-
- 用KEIL编程通过后，下载到单片机，实现时钟，并附有Proteus仿真-Programming with KEIL passed, downloaded to the microcontroller, the clock, along with Proteus simulation
24.8X8-LED_picoblaze_32_sha1
- 8X8的LED灯，有横竖两个方向通过KEIL编程下载到单片机能实现选择性灯亮，并且有仿真。-8X8 LED lights, there are two directions anyway KEIL program downloaded to the microcontroller through to achieve selective lights and a simulation.
jiaotongdeng
- 压缩包里包含单片机模拟实现交通灯的源代码和protues的仿真程序为.c放入keil中即可运行编译-Single-chip analog compression package includes the source code to achieve traffic lights and simulation program for the protues. C you can run into the keil compiler in
SHT10
- SHT 温湿度控制， 51单片机+1602液晶显示。Keil uVision2编写，有proteus仿真。-SHT temperature and humidity controlled, single-chip 1602 liquid crystal display 51. Keil uVision2 writing, there proteus simulation.
1602-LCD-remote-control
- 我上传的一个遥控1602液晶，用到的软件有两个所以只选了一个，有Keil C还有proteus仿真。-I uploaded a 1602 LCD remote control, software used in an election only two so there Keil C also proteus simulation.
wave6000w
- 伟福仿真器的驱动程序，可以用于keil的单片机程序仿真，搭配伟福仿真器适用-Weifu in emulation of driver and can be used in the simulation program keil monolithic integrated circuits, recognizes a simulation is applicable
led-character-dot-matrix-
- 本文详细介绍了基于51单片机的LED显示屏控制系统的显示原理，对16*16点阵汉字进行显示，显示屏由4个8*8的LED点阵模块组成一个16*16点阵LED。系统仿真利用PORTEUS仿真软件和KEIL软件的联调对LED点阵显示屏系统进行调试。-This paper describes the 51-based single-chip LED display control system shows the principle of the Chinese characters for 16* 1
anjian
- 调试好了的KEIL工程，PROTEUS仿真，两组按键的逻辑控制，当led1亮时led2对应的一组按键才起作用，LED1关时LED2也同时关-Well, the KEIL debugger works, PROTEUS simulation, two key control logic, when led1 bright led2 a corresponding set of keys only work, LED1 LED2 also shut off when
12_27
- 基于单片机的简易频率计,使作keil开发，在proteus 仿真通过的程序。-base on keil uv3 c promming languange