搜索资源列表
FIR_IIR
- 用matlab设计FIR和IIR滤波器的设计函数与例程-filter of iir and fir
chengxu
- 基于MATLAB的频域直接法设计IIR滤波器程序-MATLAB-based direct method of frequency domain IIR filter design procedure
firmatlab
- MATLAB环境下FIR滤波器的设计与仿真-MATLAB environment FIR filter design and simulation
FIRFilterDesign
- 基于MATLAB的FIR滤波器的设计与仿真-MATLAB-based FIR filter design and simulation
pll_frequencey_synthesis
- 基于matlab中simulink的频率合成器的设计，主要结构包括鉴相器，低通滤波器，压控振荡器-simulink based franquence synthesis,consisted of pdf,lpf,vco
Matlab6xKalman
- 基于Matlab+6x的Kalman滤波器的设计与仿真-Matlab+6 x based on the Kalman filter design and simulation
matlab_iir16
- 给出了通过matlab设计IIR低通滤波器的程序，并通过程序把在DSP中所用到的变量计算出来，很有价值。-Matlab given by IIR low-pass filter design procedures, and procedures used in the DSP in the calculated variables, very valuable.
011iir16_matlab
- 给出了通过matlab设计IIR低通滤波器的程序，并通过程序把在DSP中所用到的变量计算出来，很有价值。-Matlab given by IIR low-pass filter design procedures, and procedures used in the DSP in the calculated variables, very valuable.
011fir16_matlab
- 给出了通过MATLAB设计FIR滤波器的程序，只需要输入滤波器类型和参数就能设计出特定滤波器，并产生DSP需要的数据，很有意义。-MATLAB is given through the FIR filter design process, only the type and parameters of input filter will be able to design a specific filter, and DSP have the data needed and meaningful
MATLABDSP
- 本论文利用TI公司的16位定点DSP芯片TMS320VC5416-160的硬件、软件结构和特性实现了数字滤波器的设计。深入研究了DSP芯片的硬件开发技术和软件编程技术及调试技巧 在MATLAB环境下,利用MATLAB语言编写程序对IIR滤波器进行仿真并得到滤波器的系数 关于matlab与DSP等。-In this paper, the use of TI' s 16-bit fixed-point DSP chip TMS320VC5416-160 hardware, software
IIRfilter
- 实现IIR滤波器的原理介绍，并实现基于MATLAB的滤波器的设计实现。-IIR filter to achieve the principles of presentation and MATLAB-based filter design.
filter
- 2个程序，MATLAB设计的一个滤波器，将含3个频率分量的信号通过该滤波器，滤除2个高频分量，得到只含低频的信号。 单边带信号调制，用MATLAB实现，是学习信号调制的一个好例子。-Two procedures, MATLAB design a filter, will contain three frequency components of the signal through the filter, filter out high frequency components of two
chs-zdwc-fir-gbs
- 包括用窗函数法和最大误差最小化准则设计的FIR低通数字滤波器，并分析加矩形窗时的吉布斯现象（matlab程序）。从仿真结果可看出：采用最大误差最小化准则能得到阶数更低，阻带波纹特性更好的FIR低通滤波器，因此其效果更优。-Including the use of window function method and the maximum error criterion designed to minimize the FIR low-pass digital filter, and analy
filter_design
- 利用matlab设计滤波器，有原理说明及其matlab的代码实现-A filter was designed using matlab, there are principles of note and its matlab code to achieve the
LPQ
- 该源码是一个在MATLAB环境下设计的高通切比雪夫2滤波器。-The source code is a MATLAB environment, to design high-pass Chebyshev filter 2.
IIRdigitalFilterDesignTheory
- 一些关于IIR数字滤波器的设计理论，还有Matlab源程序，供设计数字滤波器人员参考-Some information about IIR digital filter design theory, as well as Matlab source code for the design of digital filters for reference staff
RCbandpass50Q
- 使用matlab根据50倍Q值的有源滤波器的传输函数设计各个参数跟带通滤波器的中心频率关系的M文件，可供调用-Q using matlab under 50 times the value of the transfer function of active filter design of the various parameters of band-pass filter with center frequency of the relationship between M-files ar
test
- 使用Matlab设计一个简单的滤波器小程序-Use Matlab to design a simple filter applet
GaussianClutterPowerSpectrumEstimation
- 本程序已被本人整理到WORD文档中，编程语言为MATLAB，程序中首先利用非递归法产生滤波器系数，生成相关高斯杂波，直接对杂波信号作FFT变换，结果取模平方后除以长度N,即可得到杂波的功率谱，设计参数皆在文档中表明。此程序已经验证是正确可执行的，并能生成图形，值得下载！- This program has been organized into WORD document I, the programming language MATLAB, the program produced the
GenerationOfTheLog-normalDistributionClutter
- 本程序已被本人整理到WORD文档中，编程语言为MATLAB，本文设计的滤波器采用傅里叶级数展开法。模拟的杂波的功率谱密度采用BVURG法，概率密度函数的估计采用直方图估计法，设计参数皆在文档中表明。此程序已经验证是正确可执行的，并能生成图形，值得下载！-This program has been organized into WORD document I, the programming language MATLAB, the filter designed in this paper Fo