搜索资源列表
读电机码盘的程序
- 读取一个电机码盘信号，里面有对串口读写，对控制寄存器读写的代码。入门级！-read a motor encoder signals, and they read and write to serial port, the control register read and write code. Entry-level!
abs_code.rar
- 这是用CPLD开发的读取绝对式编码器反馈的信号的代码，读取电机的转子的绝对位置和判断转动方向对于电机控制很实用。,This is read by the CPLD Development absolute encoder feedback signal to the code, read the motor' s rotor position and to determine the absolute direction of rotation is very useful for mot
motor
- 步进电机控制原理图，和完整的控制程序，安装PROTEUS后就可以看到仿真的结果-Stepper motor control schematics, and complete control procedures, installation can be seen after the PROTEUS simulation results
Motor-PID-control-code
- 应用PID控制算法，以控制电机，对其转速进行控制来编程，电机转速采用霍尔编码器进行测量，应用DSP脉冲编码捕获功能对其信号进行采集，来检测当前电机转速。-Application of PID control algorithm to control the motor speed control to its programming, the motor speed encoder using Hall measurements, application of DSP pulse code ca
shiyan6
- wode基于Proteus的步进电机仿真程序-proteus stepper motor
vhdl
- 最高优先级编码器和直流电机控制器,供初学者学习使用，方便快捷，有很强的参考价值-The highest priority encoder and DC motor controller, for beginners learning to use, convenient and has a strong reference value
dp_test
- 本程序是用VHDL语言编写的，其中包括并口通讯，DDS电机调速,编码器信号处理等，对研究这方面的工程人员有一定参考作用-This procedure is used VHDL language, including the parallel port communication, DDS motor, encoder signal processing and so on, to look at this area of engineering staff have a certain refe
CNC
- Code ASM for PIC16F628. Use for CNC/Servo Motor. With simulatio in Proteus (7.0)
DC_Motor_Multi_Speed_Simulation
- this c code written for atmega32 avr micrcontroller to show to make speed and direction control a dc motor and simulating with proteus.-this is c code written for atmega32 avr micrcontroller to show to make speed and direction control a dc motor and
DCMotorControl
- build a simple control system for a DC motor, interfaced to an encoder. Several keyboard buttons will control system operation. Use dummy software components to simulate the devices mentioned above. No physical hardware is required other than a PC wi
motor3_and_motor4
- 程序是CPLD双计数器的程序，主要用于电机编码器计数-Program is CPLD pairs of counter procedures, mainly for motor encoder counts
OpCtrl
- 步进电机的转动控制程序,可用于变速,和编码器混合使用-Stepper motor rotation control program can be used for variable speed, and mixed use encoder
aa
- proteus仿真4线步进电机控制，适合初学者学习-proteus simulation 4 wire stepper motor control, suitable for beginners to learn
Study-on-Starting-up-Method-of-PMSM-Based-on-Hybri
- 基于复合式光电编码器永磁同步电机启动方法的研究 简述了复合式光电编码器的工作原理，分析现有永磁同步电机转子位置检测方法的不足，提出了使用复合式光电编码器对永磁同步电机转子初始位置检测及电机启动的方法，最后通过以数字信号处理器(DSP)为核心的实验平台进行实验，实验结果表明，该方法可以满足实际使用的要求，实现了电机可靠启动、运行。-The operating principle of hybrid grating encoder was introduced and the shortcomi
steppermotor
- it is a stepper motor control proteus simulation using IC 890C51 and four transistor darlington array.The prpogram is written in assembly language
PWM_QEI_miniauto_V3
- 基于cpld的电机编码器源程序，很实用，精品程序-Cpld motor encoder based on source code, very practical, excellent program
at89c51proteus
- at89c51单片机proteus仿真步进电机，完整资料。-at89c51 stepper motor microcontroller proteus simulation
BLDC_Control
- 3-Phase BLDC Motor Control with Quadrature Encoder using 56F800/E
pid-
- 基于ATmega16单片机控制码盘直流电机，通过pid公式用pwm波控制电机转速-ATmega16 microcontroller-based DC motor encoder, the formula used by pid wave pwm motor speed control
STM32 ENCODER
- STM32外接旋转编码器（EC11），外部中断方式识别出正反转，响应速度优良，无丢步现象，无需延时滤波。在强干扰环境下测试正常。注意是仪器仪表面板常见的那种编码器，不是电机测速的那种。(STM32 Read Encoder (EC11), external interrupt mode to recognizes positive and negative rotation, response speed is excellent, no step loss, no delay use. The