搜索资源列表
Switch_Power
- Document expalain the work of the switch power supply with two basic type. Those are the forward mode convert and the flyback mode convert.
switch-powercircuit-basic-topology
- 开关电源拓扑结构介绍,对从事开关电源设计人员有参考意义。-Switching power supply topology introduced, in the switching power supply designers have reference value.
SM311
- pic 系列 台湾SM311芯片14脚 电源开关汇编 源程序 -Taiwan SM311 chip pic series of 14-pin power switch assembly source
buttery
- 本软件实现了对Agilent E3631A型号电源的定时开关控制,用c++编写,全部源码奉上-The Agilent E3631A software models of the timing of the power switch control, use c++ writing, all the source code offer
power-amplifier-module-
- 基于8051单片机实现对功放模块的开关控制-Based on the 8051 single chip switch control of power amplifier module
Switch-power-calculate
- switching power supply inductor design
RS232-switch-to-RS485-file
- AD 6 环境下的RS232转RS485电路原理图与pcb制版文件文件 串口取电-RS232 switch to RS485 circuit diagram and the finished document serial pcb to take power!
car
- 智能往返小车 ⑴ 车辆从起跑线出发(出发前,车体不得超出起跑线),到达终点线后停留10s,然后自动返回到起跑线(允许倒车返回)。往返一次的时间应力求最短(从合上汽车电源开关开始计时)。 ⑵自动记录、显示一次往返时间。 -Intelligent vehicles from car ⑴ starting from the starting line (before departure, the body must not exceed the starting line) to re
1.8W-Buck-Topology-Power-Supply-with-VIPer12AS.ra
- This board is an auxiliary power supply based on the VIPer12AS monolithic device with rather low output power required. It is a buck (step-down) converter with a positive output voltage referenced to the common ground based on the monolithic device V
switch-power-with-code
- 基于单片机的密码开关电源设计源码,使用c语言-microcontroller and switch power with code
ATS
- 基于51单片机控制的智能双电源转换开关汇编源码-Based on 51 microprocessor controlled intelligent dual power switch assembly source
WashingMachine
- 洗衣机系统,用VHDL硬件描述语言编程实现洗衣机控制电路。要求实现如下功能: 1.拨动电源开关,洗衣机电路进入工作状态,默认为标准洗涤程序 2.按下启动/暂停键,洗衣机开始按照既定程序工作,再按下该键,洗衣机暂停 3.洗衣机工作模式可以选择 4.洗衣机水位可以选择 每按下一个按钮,洗衣机发出“嘟嘟”警报 -Washing system, using VHDL hardware descr iption language programming washing machin
BSP450_IC-ON-LINE[1][1].CN
- BSP450,高速转换,用于电源开关。3脚是TTL电平输入,4脚是工作电压输入,当3脚作用时,4脚与1脚导通。-BSP450, high-speed conversion, for the power switch. 3 is a TTL level input pin, 4 pin is the input voltage, when the role of 3 feet, 4 feet and 1 foot turn.
Infrared-alarm-system
- 本论文设计了由AT89C52单片机为控制核心,用红外线为监测装置的防盗报警系统。该系统中红外对管作为红外线的发射和接收部分。发射部分采用红外发光二极管,而使用光敏三极管作为接收部分,接收红外发光二极管发出的红外线(不可见光)。单片机将通过内部的软件系统检测到接收管的导通或截止状态,并根据检测到的信号状态,进行判断并输出报警信号, 直至按复位按钮或电源开关。声光报警信号由9014三极管驱动构成声光报警电路,进行声光同时报警。电源部分采用变压器将220V交流市经变压器降压,桥式整流器整流,电解电容滤
002-LED
- 关闭电源后,电源指示灯呈半亮状态,这正常吗? 答:这是正常的,这个指示灯有2个作用,作用1是指示5V总电源,作用2是指示并口电平输出, 若完成学习板的使用后没断开并口线,它会作出半亮指示,若短时间内要经常使用学习板,关闭电源开关即可。 此时,不需要拔下并口和串口,指示灯的半亮状态不会影响学习板的使用。-After the closure of the power, the power indicator light is bright, is this normal?Answer:
003-Yellow-LED
- 关闭电源后,电源指示灯呈半亮状态,这正常吗? 答:这是正常的,这个指示灯有2个作用,作用1是指示5V总电源,作用2是指示并口电平输出, 若完成学习板的使用后没断开并口线,它会作出半亮指示,若短时间内要经常使用学习板,关闭电源开关即可。 此时,不需要拔下并口和串口,指示灯的半亮状态不会影响学习板的使用。-After the closure of the power, the power indicator light is bright, is this normal?Answer:
009-zhikonganjian
- 若完成学习板的使用后没断开并口线,它会作出半亮指示,若短时间内要经常使用学习板,关闭电源开关即可。 此时,不需要拔下并口和串口,指示灯的半亮状态不会影响学习板的使用。-After the closure of the power, the power indicator light is bright, is this normal?Answer: This is normal, this indicator has 2 effects, action 1 is indicative of
001-main-pro
- 关闭电源后,电源指示灯呈半亮状态,这正常吗? 答:这是正常的,这个指示灯有2个作用,作用1是指示5V总电源,作用2是指示并口电平输出, 若完成学习板的使用后没断开并口线,它会作出半亮指示,若短时间内要经常使用学习板,关闭电源开关即可。 此时,不需要拔下并口和串口,指示灯的半亮状态不会影响学习板的使用。-After the closure of the power, the power indicator light is bright, is this normal?Answer:
No.8-power-controller
- 上位机控制8路开关,可实现顺、逆开关,全开,全关,单开关。采用MODBUS通信协议。并具有掉电记忆功能-PC control 8 way switch, which can realize the, inverse switch, open, and seated, single switch. The MODBUS protocol. And has the power down memory function
STC-ISP
- 自己设计的STC单片机学习板,有完整原理图和PCB,具有STC免手冷启动功能,省去每次烧程序都按电源开关的烦恼,一个USB线,搞定所有试验!-STC microcontroller design their own learning board, complete schematic and PCB, STC hands-free cold start function, eliminating the need for each burn program troubles by the pow