搜索资源列表
51+SJA1000
- 用89C51来控制SJA1000的源码程序，C语言编写
can_bus
- 直接可用的基于sja1000+51的C源代码
can_selftest.rar
- 51+SJA1000+PA82C250构成的CAN节点，这是一个自收发的程序，程序是在硬件上运行通过的，没有问题的，里面有详细的注释，方便理解。可以为学习的提过一个参考。,51+ SJA1000+ PA82C250 posed CAN node, This is a self-transceiver procedures, procedures are adopted in the hardware to run on, and there is no problem, and there ar
51MCUSJA1000
- 基于51系列单片机的can总线驱动器 sja1000的驱动程序 本程序基于c8051f系列同样有用-Based on 51 Series MCU can bus drivers drive sja1000 This procedure would also be useful based on the c8051f Series
SJA1000_PELI_APP.H
- 1 概述 本文主要介绍了在实时操作系统Small RTOS下，编写独立CAN控制器SJA1000驱动程序的方法。并介绍了SJA1000 PeliCan模式下接口函数库的使用方法，以及简要的介绍了对Small RTOS的配置方法。 1.1 CAN控制器SJA1000 关于独立的CAN控制器SJA1000的详细介绍，请参阅参考文献1。 1.2 实时微内核Small RTOS 关于实时操作系统Small RTOS的详细介绍，请参阅参考文献2。 2 SJA1000 P
can-232
- 51单片机实现CAN总线和RS232协议之间的转换，内含SJA1000驱动程序，keil下编译通过。-51 MCU CAN bus and RS232 protocol conversion between, containing SJA1000 driver, keil compile.
EPM570
- 介绍epm570在信号采集时候的一个例子，是给予图像采集中的作用，很使用的一个例子。-Introduction epm570 signal acquisition at the time of an example are given to the role of image acquisition, it is used in a case in point.
SJA1000
- sja的使用可以参考一下。。。。有一定的参考价值-SJA1000 reset initialization mode only for that. Including working methods to initialize the settings, the way to receive filter settings, receive Mask Register (AMR) and receive code register (ACR) settings, baud rate and in
CAN_BUS
- ZLG 的SJA1000和CT1050合在一起的程序，发送接收都有。自己写的。已经调试通过。硬件用51+SJA1000，搞成外部RAM的INTEL模式即可。-ZLG the SJA1000 and procedures together CT1050, send to receive both. Wrote it myself. Have been through the debugging. Hardware with 51+ SJA1000, into the external RAM to
can-node-communication
- 该程序已经被多次使用，需要两个sja1000 + 51 + pca82c250的通讯模块（本程序是在P2.6和P2.5设置了LED灯来显示是否通讯成功），将源程序（kaobei.hex）下载到51单片机中，上电后通过按下两个模块的复位键，就能看到对应的模块有指示灯显示-The program has been used many times require two sja1000+ 51+ pca82c250 communication module (the program is set in
stc89c51-sja1000
- 基于51和sja1000的通信程序（已成功）-51 and sja1000 based communications program (successful)
51-SJA1000
- 可以实现在PC与CAN总线的连接。采用的89C51和SJA1000芯片的接法.（已实现）-Can be achieved in the PC and the CAN bus connection. The 89C51 and SJA1000 chip using the access method. (Realized)
CAN_SJA1000
- 51单片机，SJA1000的CAN控制芯片，实现CAN总线自收发，速率为1M-51 SCM, SJA1000 CAN controller chip, the CAN bus from the transceiver, the rate of 1M
89C51_CAN
- 基于89C51单片机和SJA1000的CAN总线通信测试程序，调试通过，完全可以使用。-89C51 microcontroller and the SJA1000 based CAN bus communications test program debugging, can be used.
sja
- CAN通信例程，通过51、SJA1000和CAN驱动器连接can总线，接受另一can节点发来的一个字节信息并通过LED实时显示出来-CAN communication routines, through 51, SJA1000 CAN driver and connector can bus, the node can accept another byte of information sent by a real-time LED display
SJA1000-can
- SJA1000 CAN控制器与51单片机通讯代码，调试通过，能进行CAN2.0B收发，附有芯片使用手册帮助理解代码-SJA1000 CAN controller with 51 single-chip communication code, debugging through, can CAN2.0B transceiver attached to the chip manual to help understand the code
51-sja1000
- 用51单片机作为微控制器，sja1000作为can控制器，实现can的自发自收。-51 microcontroller as microcontrollers, sja1000 as can controller can spontaneous collected.
CAN-SJA1000-V12_1-22.118400
- can总线首发程序，主要运用于51单片机上，内含中文注释，方便理解。-The can bus starting the program, mainly used in the 51 single-chip, containing Chinese comments, and easy to understand.
SJA1000-based-CAN-bus-communication
- 基于51单片机和CAN总线控制器SJA1000，CAN总线通信例程-Based on 51 single and CAN bus controller SJA1000, CAN bus communication routines
sja1000程序
- sja1000 配置c程序。。。。。。。。。。。。。。。。(sja1000 Configuring the C program)