搜索资源列表
usart
- STM32 串口通信程序 DMA 队列排序-STM32 serial communication program DMA
usart
- STM32串口初始化,实现字符串的接收和发送功能的程序-This is a program that init the serial of STM32, and it is a program that receive and send character string。
USART-TEST
- stm32多串口通信 ,经测试,很方便。保证能用。-stm32 multi usart communication
STM32F103ZET6-usart-upgrade
- stm32远程升级例程(分为boot loader区,用户区,和ota区,用户可以根据不同的需求修改启动地址)-Stm32 remote upgrade routines (divided into boot loader area, user area, and ota area, the user can modify the startup address according to different needs)
USARTPTFTLCD
- 基于STM32的编程开发,通过串口程序发送内容,然后STM32接收并显示到TFT-LCD显示屏上。-STM32 usart and tft-lcd
Crazy103_Board_V1.1
- STM32基本学习资料。包括ADC USART I2C PWM LED KEY RTC 等(STM32 ADC USART I2C PWM LED KEY RTC)
实验4 串口实验
- stm32串口调试例程,用于stm32f103的串口开发,希望对你有所帮助(stm32f10x.usart test lib(an example of Touch sensor stm32f10x.usart))
2.MPU6050程序
- STM32实现MPU6050数据传输、解码(串口2)(STM32 to achieve MPU6050 data transmission and decoding (USART 2))
7.ov7670摸索
- stm32输出color到USART 1,串口调试助手可查看某一点的RGB565值(STM32 output color to USART 1, serial debugging assistant, you can check the RGB565 value of a point)
EXTI+USART
- 外部中断使用,源地工作室stm32最小系统外部终端使用(exitThe use of external interrupt source, studio STM32 minimum system external terminal use)
stm学习中程序
- 其中包含了一个以gpio简单设置的程序以及usart通信和pwm设置的程序(It contains a program that is simple to set up with GPIO, as well as programs for USART communications and PWM settings)
DREAMER STM32开发板实验7 - 串口通信
- 通信试验,端口设置,可利用作为基本工程伸延开发(Communication test, port setting)
串口通讯
- 实现STM32串口通讯,以及OLED显示。(STM32 serial communication, and OLED display. Platform for keil DMK, engineering can be compiled to run.)
21ic下载_基于STM32的CAN总线收发程序
- 实现can通信,经本人验证完全可以使用,拿去吧。(#include "can.h" #include "led.h" #include "delay.h" #include "usart.h" #include "led.h" #include "delay.h" #include "key.h" #include "sys.h&qu
第六个工程-dma-usart
- 在mdk环境下利用stm32 f407单片机实现串口dma功能(To achieve the MDK5 stm32f407 single-chip serial port dma function)
83813466STM32-USART
- 单片机实现串口通信 中断实现数据的接收(MCU serial communication interrupt to achieve data reception)
printf(polling)
- 要让STM32能够顺利发出数据,要进行如下配置 PA9,PA10管脚要配置, USART也需要配置波特率,数据有几位,停止位,数据流等(stm32 uart communication)
Sim_USART
- 在STM32平台 模拟USART通讯(1bit起始位,1bit终止位,8bit数据,无奇偶校验)(Simulation of USART communication on STM32 platform)
BSP
- stm32吧can转接成usart can里面包含初始换 速率500kb/s usart 19200(The stm32 bar can be converted to usart which can contain the usart 19200 with an initial conversion rate of 500kb / s)
usart 升级
- stm32通过串口来升级,从uboot启动,如果不需要升级代码,则直接跳转到应用代码,如果要升级则等待串口通过secureCRT YMODE协议发送来得数据,注意(程序中由于ymodem协议没有发送文件大小,程序中是随便写了一个文件大小,对于我的app足够用),在app中随意按下按键,通过可以从应用程序跳转到uboot,然后发送1,通过ymodem协议发送.bin文件后,按下3则跳转应用程序(STM32 through the serial port to upgrade, starting