搜索资源列表
parallel-turbo-coding
- turbo 码 的 并行 编译码 有编码器，译码器，交织器，调制器，解调器等函数-The turbo code is a parallel codec function of the encoder, decoder, and an interleaver, a modulator, a demodulator, etc.
3gpp-turbo
- 一种基于3gpp标准的运行速度较快的turbo编译码程序，内含logmap，max-logmap，th-logmap译码算法，程序达到设定的错误帧数自动停止，速度快！-Based on the the 3gpp standard run faster turbo encoding and decoding procedures, containing logmap the max-logmap, th-logmap decoding algorithm, the program reaches
Turbo-code-simulation
- Turbo码仿真的matlab代码，采用sova译码和logmap译码两种方式，包括分组交织和m序列交织两种交织方式-Turbo code simulation matlab code, using the the sova the decoder and logmap decoding two ways, including packet interleaving, and m-sequence interleaving two interleaving
Turbo-Matlab
- Turbo码Matlab仿真程序,包括编译码器。-Turbo Matlab
turbo
- 主要是Turbo码的编码和译码，可以选择信噪比、 译码算法 还有图显示 可以直接使用 代码没有问题-This scr ipt simulates the classical turbo encoding-decoding system.It simulates parallel concatenated convolutional codes.Two component rate 1/2 RSC (Recursive Systematic Convolutional) component enc
turbo-source-and-simulink
- Turbo码编译码算法matlab仿真源程序基于吴宇飞教授编程源代码，以及在simulink中仿真源代码-Turbo decoding algorithm matlab source code based on Professor Wu Yufei programming source code, and the simulation in simulink source code
turbo-related
- turbo码相关的程序 以及3GPP协议 对于研究turbo码方面的朋友有很大帮助，包括编码译码等等程序-turbo codes and procedures related 3GPP protocol for the study of aspects of turbo codes friends are very helpful, including the coding and decoding procedures, etc.
turbo
- turbo码的编码与译码，交织器 coding and decoding of turbo, interleaver-coding and decoding of turbo, interleaver, almost regular permutation
turbo-codes
- 3GPP中Turbo码的三种译码算法,logmap-the decoding algrithm of Turbo codes
Turbo
- 此程序为采用matlab编写的Turbo编码和译码程序。-This program is written using matlab Turbo encoding and decoding procedures.
3gpplte_turbo_decoder
- 3gpp lte turbo译码,包括测试代码,全-3gpp lte turbo decoder
Turbo
- Turbo编译码程序，内含注释；信道编码经典程序 内含3GPP、LTE标准，已验证正确，适合学习-Turbo encode and decode, containing comments channel coding classic program Containing 3GPP, LTE standards, verified correctly for learning
turbo
- Turbo编译码程序，实现turbo编码和译码！-Turbo encoding and decoding procedures, turbo encoding and decoding
MAPturbo均衡通信系统链路
- 完整的turbo均衡链路，译码和均衡算法均为MAP，生成不同EbN0下的误码率曲线图
turbo
- 基于matlab的turbo编码。Turbo码是Claude.Berrou等人在1993年首次提出的一种级联码。基本原理是编码器通过交织器把两个分量编码器进行并行级联，两个分量编码器分别输出相应的校验位比特；译码器在两个分量译码器之间进行迭代译码，分量译码器之间传递去掉正反馈的外信息，这样整个译码过程类似涡轮（Turbo）工作。因此，这个编码方法又被形象地称为Turbo码。Turbo码具有卓越的纠错性能，性能接近香农限，而且编译码的复杂度不高。-turbo code based on matla
turbo
- 实现turbo编码和译码，并进行系统仿真，需要的拿去。-realize Turbo encode and decode,and system simulation，if you need,take it.
turbo-BCJR
- 文件中包含了Turbo码和卷积码误码率的对比，其中Turbo码采用了BCJR译码算法，迭代次数分别为1、2、3、4次。文件中包含了源代码和分析文档-File contains a comparison of Turbo code and convolution code BER, which Turbo code decoding algorithm used BCJR iterations respectively 1,2,3,4 times. File contains the source
LTE_PUSCH
- 该文件夹中包含LTE PUSCH上行链路中几个重要模块的C代码，包括了CRC添加、CRC校验、Turbo编码、Turbo译码、咬尾卷积码编码和咬尾卷积码译码6个模块。-This folder contains LTE PUSCH uplink C code several important modules, including adding a CRC, CRC checksum, Turbo Coding, Turbo decoding tail-biting convolution cod
TransmitDiversity_Mode2
- LTE下行链路发射分集仿真，仿真配置：16QAM调制、1/3码率Turbo编码、10MHz带宽、每个子帧一个PDCCH符号、单码字、8次迭代Turbo译码，每次处理1000万比特用户数据、早期终止机制、MMSE（最小均方误差）MIMO接收器，PDSCH发射端进行发射分集预编码。信道模型是LTE-MIMO信道附加AWGN信道。收发两端采用的双天线配置，天线相关性为中等。-LTE downlink transmit diversity simulation configuration: 16QAM
SpatialMultiplexing_OpenLoop_Mode3
- LTE下行链路空分复用开环。仿真配置：16QAM调制、1/3码率Turbo编码、10MHz带宽、每个子帧一个PDCCH符号、单码字，8次迭代Turbo译码、早期终止机制、MMSE（最小均方误差）MIMO接收器，PDSCH发射端进行空分复用预编码。信道模型是LTE-MIMO信道附加AWGN信道。-LTE downlink space division multiplexing ring opening. Simulation Configuration: 16QAM modulation, 1/3