搜索资源列表
board_diag
- 在fpga上关于nios开发版的测试文件,测试对象包括led,lcd,uart,内存,基本io等,对于检测硬件十分有用-they simply on the development of the nios version of the test document, including testing led, LCD, UART, memory, basic io, for the very useful hardware detection
IOUART
- 单片机IO口模拟UART演示程序,使用74HC164串行显示数据
MCU_IO_UART
- MCS51mcu用IO口线模拟UART收发
AVRM16
- AVRMega16单片机的项目,开发环境:ICCAVr6.31A,可从网上下载。 实现串口传送数据并存到AT45DB系列的FLASH芯片中,用ZLG7290显示时间、数据到数码管,读取时钟芯片,完全使用了单片机的I2C、SPI、UART、INT0、IO口等,是一个典型单片机的全功能应用项目源码实现,可直接修改应用你的项目中。绝对可靠、可用,参考价值很高。
TI CC1110 CC2510 Basic Software Examples
- TI CC1110 CC2510 範例源码 (ADC,CLK,DMA,FLASH,IO,PowerMode/PM,Radio,Random/Rnd,SleepTimer/Sleep,SPI,UART,Timer1,Timer2,Timer3/4,WatchDogTimer/WDT)
C8051F410
- C8051F410 C语言例程 包括adc,io,uart-C8051F410 C language routines
iic_uart
- I2C转UART,51单片机普通IO口模拟I2C从机,解决UART不够的问题-I2C switch to UART, 51 Microprocessor Analog IO port I2C slave address the problem of insufficient UART
MSP430F5
- MSP430F5系列中文手册,有需要的朋友可以下载一下-MSP430F5xxx--h h h h h h h h h h f f f f
IO_UART---Fujitsu
- 使用單晶片的一般IO腳來模擬 硬體 UART 通訊介面,好處為可節省hardware uart 的應用!-Fujitsu Use GPIO to simulate uart communication!
IO_382
- C51下面,用IO口模拟uart的源代码,里面有文档说明.-C51 below with IO port UART simulation of the source code, there are documented.
IOtoSerial
- C51普通IO模拟Uart,解决单片机串口不够用的问题-IO to Uart
IO_SOFT_UART_USE_TIMER
- C51很好的IO模拟串口程序,也称软件UART。只需用一个定时器,实现中断接收。程序编写得很规范,有很多个晶振频率和串口频率可选。是一个比较好的软件串口程序。-C51 a good simulation of serial IO program, also known as the software UART. Just use a timer to achieve interrupt reception. Programming very standardized, there are man
mcu_51_io_uart
- 51单片机IO口模拟串口通讯C源程,适用于AT89S51/AT89S52等单片机。-MCU GPIO uart c source code ,can use for AT89S51/AT89S52 etc.
67A04 uart
- 原厂对该功能是隐蔽的,如有需要可以参考使用附件的软件,串口对应的IO口为P16和P17(The original factory is covert to this function. If necessary, you can refer to the software that uses the attachment. The serial port corresponding to the IO port is P16 and P17)
UART
- verilog IO模拟串口,用IO模拟uart进行串口通讯,无需硬件串口(Verilog io analog serial port, using io simulation UART serial communication, no hardware serial port)
C8051F34x
- 本代码是用C8051f340 MCU对24LC256EEPROM的读写和与RS232终端以9600BPS速率通信代码.(c8051f340 demo adc ,uart ,io and so on)
new_simulation
- 通过时钟使普通的IO口模拟UART串口通讯(Use Timer_A CCR1 hardware output modes and CCR0 SCCI data latch // to implement UART function @ 2400 baud. Software does not directly read and // write to RX and TX pins, instead proper use of output modes and SCCI data // la
I2CTest_UseSoftI2CModule(PB0,PB1)
- 本程序实现了用TI LM3S系列单片机的IO端口接入I2C总线,可以实时监控总线上的变化与传输,并将I2C传输的内容,实时通过串口打印出来,可用于破解各种I2C通信协议,曾经用于解析PIC单片机之间的I2C通信,解决了串口实时打印的问题,采用FIFO,UART接受与发送均采用中断,并解决了FIFO中断深度等等问题。仅供参考。(This program is used to achieve the IO port access I2C bus by using TI LM3S Series MCU
uart_test
- 用verilog实现的一款232协议的源码,支持光纤传输,IO通道传输等等传输方式。(Verilog implementation of a 232 protocol source code, support fiber transmission, IO channel transmission and so on transmission.)
fdc代码 uart
- 18年电赛FDC2214 STM32驱动程序是FDC2214程序STM32OLED串口。IO 口全部引出硬件口全部引出硬件 IIC 接口和串口 4 单独引出,可作为 OLED 显示接口和 HC-05 蓝牙模块接口。PA13,A14,A15,PB2,PB3,PB4 不建议使用 (JTAG 或 STLink 下载口,或 BOOT 或复位(The driver of FDC2214 STM32 in the 18-year tournament is the STM32OLED serial port