搜索资源列表
ucOS-II_for_51
- 实施操作系统的设计和开发，可以一直到其他的mcu，但是要注意flash和ram-implementation of the operating system design and development, it has to other mcu. However, to the attention of flash and ram
uCOS-II-FlashLite-186.ZIP
- ucos flashlite,从中可以学到很我flash的优化技巧.-OUT flashlite, from which I can learn very flash optimization techniques.
STM32-uCOS-II_UAV.STM32 Cortex-M3下uCOS-II 2.88的最新版移植
- STM32 Cortex-M3下uCOS-II 2.88的最新版移植，包含uC-OSView GPS uCFS SD MMC驱动,STM32 Cortex-M3 under uCOS-II 2.88 of the latest version of transplantation, including uC-OSView GPS uCFS SD MMC driver
ARM7_ATSAM64_UCOS_KEIL.rar
- ATMEL ARM7 SAM64 Porting ucos / Keil ARM VER3.04。不同于其它，本代码使用了独立的中断栈，能显著降低RAM的需求，尤其适合小RAM的CPU使用。工程中已经建立了ULINK、以及H-JTAG调试的FALSH&RAM版本，因为涉及版权，不包含ucos source。,ATMEL ARM7 SAM64 Porting ucos/Keil ARM VER3.04. Different from the other, the code uses a separ
ucfs_v.3.10.rar
- File systerm from micrium ver. 3.10 with nand flash driver for NXP cpu.,File systerm from micrium ver. 3.10 with nand flash driver for NXP cpu.
Micrium-ST-uCOS-II-LCD-STM32
- uCosII2.86在STM32F10BLK1开发板上的移植例程，已完成Flash、LCD、SD、ADC驱动部分的开发，内含完整的BSP-uCosII2.86 board in the development of transplant STM32F10BLK1 routines have been completed Flash, LCD, SD, ADC-driven part of the development, the BSP includes a complete
ucos-and-YAFFS2
- YAFFS2文件系统支持页大小为2 kB的大容量Nand FI ASH 和一些具有严格写入时序如零重写要求的Nand FLAsH，是嵌入式系统中实现时Nand FLASH 管理的理想方案,附件上传的是YAFFS2文件系统移植到ucos的源代码。 -YAFFS2 file system has been added support for the new Nand FLASH with 2k bytes pages and strictly sequentia1 page writing o
fs
- ucos平台下的文件系统的源代码，支持flash、ram、IDE、smc、windowsdrive这些接口，并且还有例程。-uCOS platform file system source code, support for flash, ram, IDE, smc, windowsdrive these interfaces, and there are routine.
EEPROM_emulation
- STM32的内部FLASH的模拟的EEProm-STM32 internal FLASH simulation of Eeprom
flash_ID
- c8051f340开发外接K9F1208大容量flash存储器的源程序-c8051f340 the development of large-capacity external flash memory K9F1208 the source
disk
- uCOS 闪存读写程序，绝对好用，需要的可以-uCOS Flash reading and writing program, is absolutely easy to use, need to take a look at
ucos_for_AD
- 在DSP2812上移植ucos实时操作系统，并进行AD的采样和计算。-In the DSP2812 real time operating system on the transplant ucos and carry out sampling and calculation of AD.
uCOS-II
- 用以三星arm芯片的ucos操作系统，包括了内存管理，flash定时器和库函数等-ucos for GT2440,including flash mmu lcd and timer
ucos-i
- 基于ucos-ii的报警系统的全部源代码，非常适合ucos-ii的初学者，全部用C编写，采用的是ZLG的LPC2378模板，能稳定运行。内容包含串口读写，AT45DB161B SPI接口FLASH读写。GPIO控制等-The alarm system based on uCOS-II full source code, very suitable for beginners of uCOS-II, all prepared with C, using the ZLG LPC2378 templa
UCOS-II----IAR4.42-
- 开发环境：EWARM mcu:STM32 UCOS-II移植（IAR4.42版本） 本工程的代码存放在FLASH中（0x08000000~0x0801ffff,共128KB),堆栈和数据放在RAM中(0x20000000~0x20004fff，共20KB）。 本工程共6个任务： 任务名 优先级 功能 AppTaskStart()"Start Task" 3 初始化uC/TCP-IP,触发LED AppTaskKbd() "Keyboard" 4 读取按键和J
STM3-LED-ucos
- 基于uCOS-II的控制LED灯的闪烁；基于奋斗版STM32开发板-Based on uCOS-II,it can controling the flash of LED.
UCOS
- 采用stm32内部flash制作的flash u盘，在电脑上可以正常使用，只是空间有点小带UCOS系统，不过没有LCD显示，一大遗憾-Flash u disk using the stm32 internal flash production on the computer can be used normally, but little room with UCOS system, but there is no LCD display, a great pity ..............
LEDucgui-ucos
- 本程序主要基于STM32的硬件开发平台，使用ucosii操作系统实现了三个LED灯的轮流闪烁-The program is mainly based on the STM32 hardware development platform, use ucosii operating system to achieve three LED lights flash alternately
ucos-spark
- UCOS 基于stm32的三个流水灯亮灭程序代码-ucos spark flash
ucOS+ucGUI人机界面实验源码
- ucOS+ucGUI人机界面实验源码 加入触摸屏校准功能。 >> 校准后触摸屏参数保存在STM32芯片自身的Flash中。 >> 当第一次启动程序或者全部擦除芯片后第一次启动将会执行校准。 >> 也可以在设置功能中选择“触摸屏校准”手动执行校准，前提是当前触屏参数和真实值相差不大，可以进入到触摸屏校准选项。(UcOS+ucGUI human interface experimental source)