搜索资源列表
-
0下载:
本报告主要介绍了微机原理与接口技术的应用之一——交通灯控制器的设计与实现,主要是模拟十字路口的红绿灯,还介绍了交通灯控制器的原理以及电路接线,其中主要用到的芯片有可编程并行通信接口芯片8255A。在设计中所用到的编程语言是汇编语言,延时采用的是软件延时(即通过汇编指令)。设计所用到的备是由西安唐都科技仪器公司生产的TD-PIT+实验系统一套。在实验室将汇编程序调试通过后即可看到设计的结果。-This report introduced the Microcomputer Principle an
-
-
0下载:
液晶的驱动程序,型号是CM320240,里面有接线说明,希望对选用这一液晶的朋友有用。-LCD driver, model is CM320240, inside wiring instructions, hope to use the LCD' s friends useful.
-
-
0下载:
LCM12864字符图形液晶显示程序,程序中有具体的说明和接法,请自行查阅-LCM12864 character graphic LCD display program, the program has specific instructions and wiring, your own inspection
-
-
0下载:
介绍了基于Rogowski 线圈采集变电站中电流信号的研究与实现,阐述了系统的组成及工作原理。设
计了高压侧的硬件电路,并对器件的选择做了的具体说明,给出了低压侧信号处理的主流程图。自制了一
个 Rogowski 线圈,并做了特殊设计,给出了测试接线图。实验结果表明,自制的线圈具有良好的线性度
和较小的测量误差,可用于数字变电站中实现电流的采集。-Introduced based on Rogowski coil current signal acquisition substati
-
-
0下载:
1602显示的超声波测距,测试通过。并且内含接线说明的。-1602 shows the ultrasonic ranging, test. And includes wiring instructions.
-
-
0下载:
HY-TFT320彩屏程序 基于51 接线说明已在其中
程序分为5部分-HY-TFT320 color wiring instructions in the program based on 51 in which the program has been divided into five parts
-
-
0下载:
HY-TFT320彩屏程序 基于51 接线说明已在其中 程序分为5部分 2-
HY-TFT320 color wiring instructions in the program based on 51 in which the program has been divided into six parts .two
-
-
0下载:
HY-TFT320彩屏程序 基于51 接线说明已在其中 程序分为6部分 3-
HY-TFT320 color wiring instructions in the program based on 51 in which the program has been divided into six parts 3
-
-
0下载:
HY-TFT320彩屏程序 基于51 接线说明已在其中 程序分为6部分-
HY-TFT320 color wiring instructions in the program based on 51 in which the program has been divided into six parts
-
-
0下载:
HY-TFT320彩屏程序 基于51 接线说明已在其中 程序分为5部分 5-
HY-TFT320 color wiring instructions in the program based on 51 in which the program has been divided into five parts 5
-
-
0下载:
C51单片机LED点阵显示数字
说明 通过P0 P1 P2 作为点阵接口
要求学员掌握 LED点阵的工作原理和 各点阵脚的定义及接法,具体接线请参考接线说明 *
*我们采用的LED点阵式是低功耗,在做实验时可以用单片机脚直接驱动 -C51 microcontroller LED dot matrix display digital
Descr iption as a dot-matrix interface via the P0 P1 P2
Require
-
-
0下载:
用STC89C52写的步进电机驱动器DM422C的程序,以及电机接线说明。-Written by STC89C52 stepper motor drive DM422C procedures, and electrical wiring instructions.
-
-
0下载:
蓝牙模块,资料含主机C语言程序,从机C语言程序,模块接线说明等,推荐!-Bluetooth module, the C language program containing host language program from native C module wiring instructions recommended!
-
-
0下载:
UIP协议在STM32上的移植,本程序在STM32F103VB下测试通过
接线说明:NSS<->PD9,SCK<->PA5,MISO<->PA6,MOSI<->PA7-Transplantation of UIP protocol in STM32, this procedure in STM32F103VB under test
Wiring instructions: NSS<->PD9, SCK<->PA
-
-
0下载:
UIP协议在AVR单片机+ENC28J60上的移植实现,熔丝位设置:低位[CE],高位[99],扩展位[FF]
接线说明:SPI的三根线直接连接,CS片选接到mega64单片机的PB0 SS即可。-In AVR to achieve+ENC28J60 microcontroller on the transplantation of UIP protocol, fuse bit settings: low [CE], high [99], extended [FF]
Wiring
-
-
0下载:
长线步进马达试验,内含5个小实验及接线说明-Long term stepper motor test, with 5 small experiments and wiring instructions MCU
-
-
1下载:
本程序是使用STM32开发蓝宇第四代线性CCD的例程,附有CCD与STM32的接线说明。程序是基于STM32F103ZE单片机的,可移植。-This procedure is the use of STM32 development Lan Yu fourth generation linear CCD routines, with CCD and STM32 wiring instructions. The program is based on the STM32F103ZE microco
-
-
0下载:
接线说明;
Trig ------- P2^1;
Echo ------- P2^0;
VCC -------- +5v
GND -------- GND
请在上电之前,检查好接线是否正确。(Wiring instructions;
Trig - P2^1;
Echo - P2^0;
VCC - +5v
GND - GND
Please check that the wiring is correct before power on.)
-
-
0下载:
wiring instructions for inverter INVT GD10
-
-
1下载:
RK3288 硬件设计说明,详细的硬件布线说明,很有用!(RK3288 hardware design instructions, detailed hardware wiring instructions, very useful!)
-