搜索资源列表
shujulianluchuanshu
- 主要实现的是能够在同一个显示屏里面能至多接收六路相同或者不同的数据。当数据不正常的时候,能进行报警;能够对数据有一定的分析能力!当信号接收到以后,我们在信号静止的情况下能对信号的周期和幅度进行分析-main achievement is to be able to display the same one which can receive up to six different routes or different data. When the data are not normal tim
TDA2320_IcpdfCom
- 这是红外遥控信号接收集成电路的技术资料,对与相关嵌入式系统开发人员大有用处-This is the infrared remote control receiver IC technical information, related to embedded system developers very useful
CANzongxianyuxiaofangshebeijiekou
- CAN总线与消防设备接口:由于大多数消防设备都采用RS232标准的串口通讯,因此,我们可以充分利用51系列单 设备传来的数字信号接收进来,放入一个缓冲区中,按CAN数据传输协议打包成CAN数据包后,再 之也可。
TestQTest
- 基于RS232通信协议实现开关量信号接收-based RS232 communication protocol switch signal reception
SerialPort
- 这是一个在LABVIEW上实现的使用LABVIEW自己产生信号,然后将上述波形采样,并通过串口发送,把上述信号存在特定的文件里,同时能实现回放,最终接收端接收串口数据,并构建波形。-This is implemented on a LABVIEW generated using LABVIEW own signal, and then the waveform samples, and sent through the serial port to the signal the presence
wcdma_ccode
- wcdma系统的仿真,c语言编写。包括发射、接收、信道、信号检测的程序。可以整体运行。-WCDMA system simulation, c languages. Including the transmitter and receiver, channel, signal detection procedures. Can the overall operation.
qiweibakema_f
- 设雷达信号是码宽为0.5微妙,中心频率是10MHz的7为巴克码2PSK信号,接收的雷达回波中频采样频率为40MHz,中频进行正交下变频。假设在13.5km处有一个点目标,仿真该雷达的脉冲压缩处理。-Code-based radar signal is a delicate relief of 0.5, the center frequency is 10MHz for the 7 Barker Code 2PSK signal, the radar echo received IF sampli
15278_40f4e9ec7d
- 红外接收放大电路,把接收到的小信号进行对做红外的有帮助-Infrared receiver amplifier to receive small signals on the IR so helpful
1234(2)
- 接收译码电路由红外接收放大器、音频译码电路和声控执行电路组成。接收红外二极管应采用与红外发射管配对的管,在收到红外光脉冲后,接收管D1的两极间电阻作与频率相应的变化,由光信号转化为电信号,经VT1和IC1放大-Received by the infrared receiver decoding circuit amplifier, the audio decoding circuit and voice-activated circuit implementation. Should be us
byVB
- 涉及双音多频制式电话按键拨号的原理, Goertzel DFT算法实现DTMF 拨号过程,在发送端根据具体的电话号码生成相应的双频信号,在接收端根据频谱幅度,找到ASCII码即检索出电话号码。用VB进行可视化编程设计及仿真-DTMF,Goertzel DFT
direct-sequence-spread-spectrum
- 带干扰的直接序列扩频通信系统,PN码由m序列产生器产生,经过高斯白噪声信道。在接收端接收到的信号包括“有用信号+高斯白噪声+干扰”,将接收信号进行解扩,判决,得到用户的信号检测结果,绘制不同的扩频增益(增益值为10,30,50)下,误比特率随信噪比Eb/N0的变化曲线。-the direct sequence spread spectrum with interference communication system
zi
- 在本系统中,信息序列在先经过FSK调制,经过截止频率为25kHz的低通滤波器后(把信号频率限制在25kHz),再进入混频器搬移到更高的频率发送出去,在接收端,用与发送端同步的跳频信号对其进行变频(跳频的解跳处理在此进行),取下边频,然后进行FSK的解调-In this system, the message sequence prior through FSK modulation, through the cut-off frequency of 25kHz after low-pass fi
PCpidcontrol
- 两路PID回路信号接收并使用ntgruf控件显示跟踪轨迹和PID参数设定。-Two PID loop control signal to receive and display tracking using ntgruf track and PID parameters.
c-chengxu
- DMX512 信号接收,用STC12系列单片机开发,适用于初学者练习DMX512信号控制的舞台灯具-DMX512 signal receiver, STC12 Series MCU development for beginners to practice DMX512 signal control stage lighting
first_experiment
- 用于卡尔曼滤波,静态GPS信号接收时,对GPS信号进行分析-Kalman filtering is used, a static GPS signal reception when the GPS signal is analyzed
谱分析
- 雷达接收信号频谱分析(幅度和相位)-matlab实现(Radar receiver, signal spectrum analysis, matlab implementation)
URG
- 激光传感器库函数,将传感器的距离数据信号接收并以图形的方式显示出来(The laser sensor library functions to receive the sensor's distance data signals and display them graphically)
full coherence
- 通过两个雷达平台相位编码信号的发射验证接收相参N方的信噪比增益; 再利用相同信号的发射接收验证收发相参N立方的信噪比增益。(Signal to noise ratio gain of coherent N receiver is verified by transmitting phase coded signals from two radar platforms; The signal-to-noise ratio gain of transceiver coherent
Single_Array_Original_Data_Generation_
- 用MATLAB的编写的声纳等距离线阵列的原始信号接收的程序(The program of receiving the original signal of the sonar equidistant line array written by MATLAB)
shiyan
- EGC MRC SC 信号多信道下的传播,多种接收方式,实现信号接收(EGC MRC SC signal multichannel propagation, multiple reception methods, signal receiving)