搜索资源列表
Transfer-matrix-methods
- 计算一个8自由度转盘扭转系统的固有频率和描述其主振型。-It is a computer program to calculate all the 8 natural frequency and the corresponding normal modes of torsional vibration of the rotor system using matrix iteration method or transfer matrix method respectively.
m11e
- 机械动力学系统中力学模型分析，求得它固有频率，振型，主坐标。-Mechanical model analysis, mechanical dynamic system to obtain its natural frequency, mode shapes, principal coordinates.
motaicansu
- matlab 基础上通过最小二乘法进行模态参数识别，得出固有频率，振型，阻尼比，图形-by the least squares method matlab based on the identification of modal parameters obtained natural frequency, mode shape, damping ratio, graphics
matlab
- 析该半车模型的固有频率和阻尼比，每一个固有频率为模型中那一个部件的主要振动，-half car inherited frequency
Shell
- MINDLIN法快速法圆锥壳固有频率求解方法-MINDLIN Rapid method for solving method conical shell natural frequency
home-work--of-vehicle--vibration
- 汽车系统动力学的大作业，编程作业，里面有阻尼比的分析，固有频率的分析，悬架性能的参数评价-Automotive systems dynamics major operations, programming assignments, there are damping ratio analysis, natural frequency analysis, the parameters of suspension performance evaluation, etc.
vibration
- 振动分析matlab程序，用于固有频率振型求取。-vibration analysis matalb code
compute-fre
- 基于Matlab的多自由度系统固有频率及振型计算-Matlab multi-degree of freedom system natural frequencies and mode shapes is calculated based on
fangzhen
- 用matlab仿真轴承故障信号构造轴承故障的仿真信号，其中轴承的固有频率fn=3000Hz , 位移常数y0=5, 阻尼系数ξ＝0.1, 冲击故障发生的周期为0.01s，采样频率fs=20KHz, 采样点数N=4096。要求：根据上述条件构造轴承故障的仿真信号，画出其时域波形及频谱图。-Matlab simulation bearing fault signal
plate_fem
- 用三角形单元计算不同边界条件下平板固有频率和模态-alculated under different boundary conditions tablet natural frequency and modal
bsxsceng
- 这个算法采用有限元八个节点的方法方法用于计算板板的固有频率的-The algorithm method using the finite element method to eight nodes for calculating the natural frequencies of the plate board
2D-Truss-Vibration
- 本代码用于模拟二维桁架结构在外载激励作用下、存在动力吸振器的情况下的响应情况，完全原创，只有一个m文件用于生成桁架振动动画的avi文件，其余三个函数用于辅助生成具体桁架结构的参数以及辅助计算。外载荷频率、动力吸振器固有频率可以通过改变代码中的变量来控制。-This code is used to simulate the two-dimensional truss structure as set out under the incentive, there are circumstances
chuandi
- 适用于盘轴系统的固有频率求解和分析，不但可以得出固有频率还能获得振型和弯矩特性-Is suitable for solving and analysis, the natural frequency of the shaft system not only can get the inherent frequency vibration mode and bending moment characteristics can be achieved
subspace_iteration
- matlab程序，子空间迭代法求固有频率及阵型-subs_iteration method to get frequency and mode shape
jiaodianjiajiao
- stewart上平台近铰接点夹角对系统固有频率分布影响研究-Study on the influence of the angle of the near hinge contact on the natural frequency distribution of Stewart
cantilever--vibration-analysis
- 悬臂梁在冲击振动下，通过MATLAB编程，比较有限元方法和模态叠加法下加速度谱识别固有频率效果-In Izod impact vibration by MATLAB programming, at a relatively finite element method and modal superposition method to identify the natural frequency spectrum of the acceleration effect
platenew1
- 平板固有频率求解编程，用matlab打开(The natural frequency of the plate is solved by MATLAB)
decRation
- 用于发动机悬置解耦的程序，发动机悬置系统解耦率、固有频率程序(Program for decoupling of engine mounting, program of decoupling rate and natural frequency of engine mounting system)
matlab-有叶盘-梁模型
- 可以计算模型固有频率,给出质量矩阵和刚度矩阵即可，理论方法和有限元法(calculate the natral characteristics)
Desktop
- 该MATLAB脚本为使用矩阵迭代法计算其固有频率及振型，(Matrix iteration method for calculating natural frequencies and modes)