搜索资源列表
ListCtrlDemo
- ListCtrl显示数据,通过按键添加显示,删除显示,清空显示。通过复选框选择需要显示的数据。-ListCtrl display data displayed through the button to add, delete, display, clear display. Select the data to be displayed by the box.
light-led
- LED 点亮+按键程序+数码管显示。综合实现LED与数码管之间的调试-lightLED and show
CT
- 双路输出控制器”具有信号输出时间设定、 输出信号占空比调整、 当前输出通道及时 间显示、系统工作参数存储、串口通讯及 LED 指示等功能。 “双路输出控制器”通过串口完 成信号输出时间设定功能;通过 EEPROM 完成系统工作参数存储功能;通过按键完成输出通 道切换、 输出信号占空比调整及停止信号输出功能; 系统硬件电路主要由 MCU 控制单元、独 立按键、 LCD 显示单元、 串口通讯单元、 EEPROM 数据存储单元和 LED 指示单元组成-Dual output contr
exercise1
- win32 SDK 自汇按键,能够显示文字和图片,并且能够修改文字与图案-win32 SDK create buttons with text and pictures,that you can change test and pictures with it~!
commandbox.
- VB第一个测试程序,用控制按键控制显示和隐藏标签-VB first test program, using the control buttons to control the display and hide the labels
liangludianyabiao
- 两路数字电压表 数码管显示通道和所得电压 通过按键控制-Two way digital voltmeter
dianzibiao
- 本系统以STC89C53单片机为控制核心,通过与DS1302和DS18B20通信获取实时时间和实时环境温度,并将得到的数据处理后通过LCD12864液晶屏显示出来,同时通过ISD1760进行语音报时以及闹铃提醒。功能按键可以选择功能,调整时间等。因此本设计可分为以下模块:单片机模块、显示模块、实时时间计算模块、实时环境温度采集模块、语音报时模块、电源模块、按键模块和PM2.5检测模块。-This system STC89C53 microcontroller core, through comm
DHT11-mearing-program
- 基于51单片机的DHT11温湿度传感器的温湿度测量报警系统,通过三个按键设置温湿度报警上下限,并存储设置值于eprom中,在LCD1602上显示温湿度值,通过蜂鸣器进行报警。-51 microcontroller-based temperature and humidity sensors measuring temperature and humidity DHT11 alarm system, via three buttons set upper and lower limits of t
LH20114680
- 本文主要介绍以超声测距的原理为理论基础,以Freescale MC9S12XS128单片机为核心,设计一个包含超声传感器模块、温度传感器模块、液晶显示屏LCD1602模块、语音芯片ISD1760模块和基本操控按键的综合电路系统。单片机最小系统电路板直接借用S12X核心开发板,其它电路施行搭建连接。硬件电路设计完成后,进一步完成红外测障、超声测距和现场温度检测的软件编程,并将相关检测结果在液晶显示器上显示和语音播报。-This paper introduces the principle of u
lcd
- 按键控制LCD1602实现时间的显示和调节-the keys control lcd1602 and times
LED
- 16*32位点阵字符显示与控制代码,加按键移位-16* 32 dot matrix characters display and control code, add button shift
Key-Value
- 根据键盘输入的按键在win32控制台窗口显示按键键值。-Display button keys in win32 console window according to keyboard input keys.
key
- 按下独立按键的相对应键值,数码管上显示相应的按键值。-Press the corresponding key independent keys, the corresponding key value of digital tube display.
51MCUjiaotongdeng
- 设计交通信号灯控制系统。 1)一路延时60S,一路延时40S,演示时为节省时间,一路延时15S,一路延时10S,两路时间分别用不同的数码管显示; 2)倒数3S时,黄灯闪亮; 3)紧急通行控制,如某一方向现为红灯,通过按键强行切换为绿灯,而另一路改为红灯,延时若干秒(10S)后,恢复原状态(红灯)继续倒数。-Design of traffic signal control system. 1) all the way to delay 60S, all the way to del
user
- STM32-595显示C程序,按键控制电机。可实现电机的参数设定。-STM32-595 show C programs, the key to control the motor. Enables parameter setting of the motor.
Waveform-Generator
- 内含C文件,以C51为基础,proteus软件实现使用DAC0832 输出波形可使用按键进行正弦波、三角波、矩形波的输出,可进行波频率的调节LCD显示波的频率等-Contains C files to C51-based, proteus software using DAC0832 output waveforms using the keys sine wave output triangle wave, square wave, the wave frequency can be adju
Matrix-button
- 以C51为主采用HC573进行proteus仿真,矩阵按键可实现乘法输出,输出结果显示在数码管上,显示六位-In C51-based HC573 conducted using proteus simulation, matrix multiplication button enables output, the output is displayed on the digital tube display six
Console_hellow
- 基于对话框的基本编程显示,显示hellow的对话框,包含按键编辑框等-Based on the dialog box shows the basic programming, display the hellow dialog box, including the button edit box, etc.
LCD12864
- 功能说明: 单片机:STM32103xx 外设:LCD12864液晶显示模块 送数据方式:并行 功能描述:数字时钟 通过4个按键来进行设置时钟 Key1、修改 Key2、加 Key3、减 Key4、确认 Key5、清零 附加功能:显示整型变量 、显示浮点型变量 - Function descr iption: Single chip microcomputer: STM32103xx
51--24hours
- 数码管显示可调24小时时钟,附有ISIS 7 Professional仿真电路图,三个按键分别对时、分、秒进行调节。-Digital display adjustable 24-hour clock, accompanied by Isis 7 professional circuit simulation, three buttons, etc, minutes and seconds to adjust.