搜索资源列表
BCDlight1998
- Proteus仿真51单片机控制多位数码管显示,BCD码控制数码管动态显示。 -51 microchip circuit system,simulated by proteus software ,control seven-segment lights.
plj
- 基于51的频率计,数码管显示,程序通俗易懂,对单片机学习者有一定的帮助-51 Based on the frequency meter, digital display, user-friendly procedures for single-chip to help learners have a certain
shumaguan
- labview做的数码管,用labview做的数码管啊-The digital control labview, labview to do with the digital control ah! ! !
maikuanceliang
- 能够对输入的脉冲信号用10HZ时钟进行计数,输出计数结果。系统有三个状态:准备测量状态、测量状态、测量完毕状态。在准备测量状态下,测量结果显示为全零,内部计数器不计数,仅当待测脉冲按键SW12被按下时(按下后,输入到FPGA引脚的为低电平)进入测量状态。在测量状态下,只要待测脉冲按键一直按下,则内部计数器一直加计数并同时显示计数结果,这个结果用两个数码管L7,L8指示,从“00”到“FF” (如果计数超出量程即超出“FF”,则需锁存一个溢出信号让溢出指示灯D29亮)。仅当待测脉冲按键松开时进入测
yifenzhongjishi
- 一分钟计时器 计时一分钟后清零 LED数码管显示 -One minute after the timer for one minute time Clear LED digital display
shumaguanshijianC
- 数码管显示时间的KEILC程序(无需设计初始时间)-Digital display of time KEILC procedures (without the design of the initial time)
clock
- AT89C51最小系统板时钟程序,四位数码管静态显示分和秒数据,仅供参考-AT89C51 minimum system clock board procedures, the four digital tube display minutes, and seconds of static data, for reference only
MyClock
- 在code网站下的数码表钟,可以用于水利,电力等项目-Site in the code of the digital table clock that can be used for water conservancy, electric power project
AD
- 基于avr单片机实现AD转换,A0口输入模拟量,D口连接数码管-Avr-based MCU AD conversion, A0 analog input port, D I connect the digital control
SMG18b20
- 这是一个基于8051单片机的DS18B20温度显示程序,通过数码管来显示,感觉不错。-This is a 8051 based on the DS18B20 temperature display program, through the digital control to display, I feel good.
HC164-drivendigitalcontrolofstatic
- 四位静态数码管演示程序,利用定义好的字符代码非常方便的显示任意数码-Four static digital control demonstration program, using the definition of good character code is very convenient digital display of arbitrary
STC89C51tiaoshichengxu
- 这是所有STC89C51的调试程序,希望对有用。包含了LCD,数码管,流水灯-This is all the STC89C51 debugger, in the hope that useful. Includes LCD, digital tube, water lamp
miaobiao
- atmega16的T0产生秒表,用数码管显示,有proteus仿真。适用于初学者。-T0 the atmega16 have a stopwatch, digital display, and proteus simulation. Apply to beginners.
verilog2
- 本代码在Quartus II 9.0 (32-Bit)环境编译运行,使用SOPC_NIOSIIFPGA开发板,可作为入门级代码讲解,将50MHZ的频率改为1MHZ,并以此频率为基准计数显示在七段数码管上。(采用verilog语言)-The code in Quartus II 9.0 (32-Bit) environment to run the compiler, the use of SOPC_NIOSIIFPGA development board, entry-level code ca
xianshishuzimoban
- 数码管显示数字的万能学习模板,vc开发,在此模板的基础上可添加自己的各种实际需求。-Digital display digital template of universal learning, vc development, in this template can be added based on the actual needs of a variety of their own.
a
- 测试开发板的源程序,按键等最基础的功能用于测试数码管,流水灯继电器。-Development board to test the source code, keys of the most basic functions, such as for testing of digital pipes, water lamp relay.
CLOK
- 时钟分频。使用原有高频信号,将其10倍频,得到可用于八段数码管显示的扫描信号-Clock frequency. The use of the original high-frequency signal, frequency-doubling of its 10, the eight can be used to display the scanned digital signal
miaobiao
- 用动态扫描方法和定时器1在数码管的前三位显示出秒表 精确到1 秒,即后两位显示1 秒,一直循环下去-have not
shumaguanxianshi
- 利用动态扫描和定时器1在数码管上显示出从765432 开始以1/10秒的速度往下递减直至765398并保持显示此数 与此同时利用定时器0以500MS速度进行流水灯从上至下移动 当数码管上数减到停止时,实验板上流水灯也停止 然后全部开始闪烁3秒后(用T0定时) 流水灯全部关闭数码管上显示出“HELLO”。到此保持-have not
miaobiao1
- 用动态扫描方法和定时器1在数码管的前三位显示出秒表 精确到1 秒,即后两位显示1 秒,一直循环下去。实现按第一个键秒表停止计数,按第二个键开始计数,按第三个键清零-have not