搜索资源列表
信号的产生
- 2、产生单位冲激函数(unit impulse),单位阶跃函数(unit step),单位斜坡函数(unit ramp)-2, the units have impulse function (unit impulse), Step function units (unit step), flat slope function (unit ramp)
信号的产生补遗
- 2、产生单位冲激函数(unit impulse),单位阶跃函数(unit step),单位斜坡函数(unit ramp)-2, the units have impulse function (unit impulse), Step function units (unit step), flat slope function (unit ramp)
fftseq
- 基于matlab的各种模拟信号的产生,如阶跃信号,正弦函数,三角函数等-based on the Matlab the analog signal generated, as a step signal sine function, trigonometry, etc.
lisanxiangshi
- 离散相似法在计算机上进行计算机仿真计算 其中输入为阶跃函数,幅度为1-discrete similarity in the computer on the computer simulation to calculate the input step function, a range of
WONDERFULMATLABWORKS
- 文件当中题意如下:已知一个二阶欠阻尼闭环系统,其传递函数G(s)=20/s2+3s+20 .输入信号为单位阶跃信号.求: (1):解析解 (2):用四阶R—K方法及Adams预估校正法求数值解. (3):比较用四阶R—K方法不同步长时计算精度与解析解进行比较,结果以图形给出. (4):给出用Adams做出的阶跃响应图形. 本文档解析透彻,有完整的源程序和仿真图形,对学习的朋友很有借鉴意义。
motorcontrolsimulate
- 用matlab实现motor运动控制的控制器设计仿真,包括有状态方程建模、levy拟合法、阶跃响应方波转换等方法。
fibercalppt
- 求解阶跃型光纤理论的演示文稿,很有帮助哦
xinhaoxitongppt
- 1.1 绪 言 一、信号的概念 二、系统的概念 1.2 信号的描述与分类 一、信号的描述 二、信号的分类 1.3 信号的基本运算 一、加法和乘法 二、时间变换 1.4 阶跃函数和冲激函数 一、阶跃函数 二、冲激函数 -1.1 Introduction of a signal of the concept of the Second, the system the concept of 1.2 signals a descr ipti
dgao
- 飞行器纵向回路姿态控制系统中阶跃干扰时定高平飞-Aircraft vertical loop attitude control system in step interference Gaoping set to fly
ISPID
- 离散系统的数字PID控制仿真和采用积分分离式PID控制器进行阶跃响应.-The number of discrete system simulation and the use of PID control points separate PID controller step response.
feixianxing
- 非线性控制,在matlab中进行二阶对象的非线性仿真,研究其阶跃响应。-non-linear control
yichuan
- 关于遗传算法在MATLAB中对典型二阶对象进行仿真,并得到其阶跃响应-MATLAB
chap5_3f
- 关于神经网络算法在MATLAB中对典型二阶对象进行仿真,并得到其阶跃响应-MATLAB
chap5_3f0
- 有关遗传控制算法在MATLAB中针对典型二阶对象进行仿真得到阶跃响应。 -MATLAB
mygui2
- 归一化二阶系统的阶跃响应曲线,MATLAB初级图形演示系统-Normalized second-order system step response curves, MATLAB junior graphic demonstration system
kalman
- kalman观测器的设计例子,并且对设计出来的系统进行阶跃响应,可观测响应图形-kalman observer design example
frac_step
- 自动控制系统中分数阶系统的阶跃响应绘制方法,类似于整数阶系统(step response of fractional-order system)
PE_step
- 针对扰动为阶跃信号的单变量系统进行性能评价(Performance evaluation of a single variable system with disturbance as step signal)
Documents
- 计算斜阶跃关断响应的瞬变电磁程序,分成4个部分(Transient electromagnetic program for calculating oblique step off response)
question1
- 编制阶跃响应与方波响应相互转化的程序、由阶跃响应数据获得对象传递函数模型的通用程序、由阶跃响应数据获得对象微分方程模型的通用程序。并通过一个传递函数进行验证(阶跃响应和方波响应数据可利用simulink生成)(A program for converting step response to square wave response, a general program for obtaining transfer function model from step response data,