搜索资源列表
dlb_ode
- matlab源码，倒立摆仿真程序，对象为：垂直悬臂-摆杆一阶倒立摆-Matlab source, the inverted pendulum simulation program, is designed for : vertical cantilever-placed shot an inverted pendulum bands
FEM
- 有限元设计_悬臂梁承载 -Finite element design _ cantilever load
wanqugandejisuan
- 弯曲杆的计算，包括悬臂梁、简支梁、外申梁，可计算集中力、力矩、分散力的效果，可由图形显示。-Bending under the terms, including the cantilever, simply supported beam, outside the申梁, concentration calculation, torque, the effect of scattered power by the graphical display.
work4_3
- function work4_3 本程序为有限元导论作业4，采用4个4节点矩形单元计算平面悬臂梁A点的挠度-function work4_3 Introduction to the finite element program for the operation 4, using four 4-node plane rectangular element calculation of the deflection of cantilever A point
combine--load-chart
- 钻井船悬臂梁loadchart计算 ,计算悬臂梁升出船体所能承受的井心与立根盒的最大载荷。-Calculate the cantilever rigs loadchart
meshless--EFG(OK)
- 无网格伽辽金二维的悬臂梁位移的计算，可以运行，学习无网格法的好程序-Cantilever displacement of grid computing without Galerkin, you can run a good learning process Meshless Method
fem_NR_ai
- New-Raphson法用于悬臂梁验证，求通过，向下载个源程序-New-Raphson method is used to verify cantilever, New-Raphson method is used to verify cantilever,
jiechuwang
- 接触网腕臂计算的可视化界面编程（适用于平腕臂）-Catenary cantilever computing visual programming interface (suitable for flat cantilever)
simple_beam
- 一个简单的悬臂梁基于Python有限元程序，包括了计算程序，模型数据-A simple cantilever Python-based finite element program, including a computer program, data model
Cantilever-displacement
- F 100KN；l 10m；A 1000mm2；E 210KN/mm2。用有限元法进行结构分析。-F 100KN l 10m A 1000mm2 E 210KN/mm2. Structural analysis by finite element method.
ieementvdeflectionvFinite
- 有限元设计,悬臂梁承受荷载的变形情况,有图形显示,-Finite element design, the deflection of the cantilever beam under load, graphic display,
cantilever--vibration-analysis
- 悬臂梁在冲击振动下，通过MATLAB编程，比较有限元方法和模态叠加法下加速度谱识别固有频率效果-In Izod impact vibration by MATLAB programming, at a relatively finite element method and modal superposition method to identify the natural frequency spectrum of the acceleration effect
Cantilever_Constrain_General_left
- 用于损伤识别的其中一个例子，悬臂梁的公式(One example of damage identification is the formula of cantilever beam)
FEM
- 几何线性悬臂梁的程序，用户可以在此基础上修改参数计算位移变形。或者增加节点计算位移(The program of a geometrically linear cantilever beam, the user can modify the parameters to calculate the displacement and deformation on this basis.)
Unimorph
- 压电悬臂梁，本振方程的构建，输出电压，共振频率的选择(Piezoelectric cantilever beam, the construction of the local vibration equation, the output voltage, the selection of resonance frequency)
EFGM
- 无网格二维悬臂梁受集中荷载伽辽金法matlab源程序(Meshless two-dimensional cantilever beam source program)
Cbeam
- 悬臂梁自由梁振动振型，可以根据要求设置尺寸、材料参数(The free beam vibration mode of cantilever beam can set the size and material parameters according to the requirement.)
beamactivecontrol
- 通过MATLAB语言的编程，可实现悬臂梁振动控制的模拟，参数可调整。(Cantilever beam vibration simulation can be achieved.)
xuanbiliang
- 以悬臂梁为例，用有限元法编程生成质量矩阵和刚度矩阵（采用平面梁单元，单元数在10到30之间）。 使用matlab的用于广义特征值问题分析的函数（eig(A,B,'chol')，该命令使用乔莱斯基分解的方法，计算对称矩阵A和对称正定矩阵B的广义特征值问题。A对应刚度矩阵，B对应质量矩阵）计算梁的前三阶固有频率和振型，计算得到梁的前三阶固有频率和振型，并画出振型图。(Taking cantilever beam as an example, the mass matrix and stiffness
pieaoelectric
- 采用MATLAB求解压电悬臂梁响应的程序，结果准确(Using MATLAB to calculate the response of piezoelectric cantilever, the result is accurate.)