搜索资源列表
DSW
- P10 （P0）与J12 JP9(P3)与JP5 用8PIN排线连接,P3.2和P3.3外部中断输入 由两个四位数码管分别显示计数-P10 (P0) and J12 JP9 (P3) and JP5 cable to connect with 8PIN, P3.2 and P3.3 external interrupt input consists of two four digital tube display counts
DSW
- 改变学习板上的2个电位器对应的2段模拟输入，实现模拟输入，学员观察数码管的数字变化情况,通过改D[4]的值，实现模拟输出.-Changing the learning board two potentiometers corresponding paragraph 2 analog inputs, analog inputs, digital tube digital trainees observe the changes, by changing D [4] value for analog
dsw
- 了解 DS1302时钟芯片的基本原理和使用，掌握DS1302时钟芯片驱动程序的编写以及实现数字字符在数码管中的显示。-Learn the basic principles DS1302 clock chip and use master DS1302 clock chip driver for the preparation and the realization of numeric characters in the digital tube display.
DL
- 用按键控制多路电压的测量，上电复位时，数码管定时显示8路电压值；按键时，可精确到哪一位，外加报警程序。-With keypad control, multi-channel voltage measurement, power-on reset, the digital time display 8 voltage value button, where an accurate, plus alarm program.
keyboard-detection-program
- 4*4键盘检测程序,按下键后相应的代码显示在数码管上。-4* 4 keyboard detection program, press the corresponding key code is displayed on the digital pipe.
shumaleichengxu
- 关于STC89C52单片机的数码类程序!主要是单片机的程序-About STC89C52 singlechip digital program! Mainly is the MCU program
Key
- 这是单片机键盘程序，按键数码管显示数字，基于P89V51单片机-This is the SCM keyboard program, key digital display digital, microcontroller based P89V51
dianji
- avrM16按键控制直流电机转速数码管显示-avrM16 DC motor speed control buttons
iiceeprom
- 用IIC协议24C02记录开机次数数码管显示-IIC protocol 24C02 boot record with the number of digital display
clock
- 用单片机AT89C51采用中断方式，实现定时与计数功能，并用4位数码管显示-MCU AT89C51 using interrupt mode, to achieve timing and counting functions, and use four digital display
108-PCF8591
- 适合初学者学习AD芯片PCF8591芯片的应用，采集一路AD进行数码管显示，可以调节外部电位器来改变电压值。-Suitable for beginners to learn AD chip PCF8591 chip applications, collecting all the way to AD digital display, external potentiometer can be adjusted to change the voltage value.
111
- 基于单片机ATmega16实现数码管显示数字的实验教程-ATmega16 microcontroller based digital display digital realization experimental tutorial
DigitalLED
- 数码管显示的控件，可设置颜色、位数、线宽等。-Digital display controls, you can set the color, the median line width.
Ordinary-clock-timer
- 普通定时器时钟，三个按键对时间进行调整，利用数码管显示，在51开发板上检测成功。-Ordinary clock timer
temp_18b20
- 温度传感采集，有数码显示功能，用于51单片机，测试可行-Temperature sensor acquisition for 51 single chip microcomputer, With digital display function 。test is feasible
RB-Level-Change-Interrupt
- RB端口电平变化中断控制两位数码管开关与加减显示，C语言编程，并配有proteus仿真电路。-RB port change interrupt control two switches with digital subtraction display, C language programming, and is equipped with proteus simulation circuit.
naozhong
- C-51单片机数字钟，两路闹钟，可任意调节，共阴数码管显示。-C-51 singlechip digital clock, two alarm clock, can be arbitrary regulation, common cathode led display.
ZLG7289
- zlg7289控制程序，可以控制zlg7289的键盘和数码管显示程序-zlg7289 control program, you can control zlg7289 keyboard and digital display program
jichushiyan-shumaguan
- 基于ARM内核的M051单片机数码管基础实验，有助于ARM内核的入门-M051 digital microcontroller based on the ARM core-based experiments to help ARM core entry
8digit-display
- 8位数码管中第一位显示,V573需要用短路帽短接到VCC，不用时需要8位数码管中第一位显示-8digit display