搜索资源列表
bii
- 无线遥控\安防报警\单片机,语音处理,电机控制门-Wireless remote control \ security alarm \ SCM, voice processing, motor control gate
Code
- dsp例子程序，包括滤波器，FFT，电机控制等-dsp examples of procedures, including filters, FFT, motor control, etc.
C51DCMOTORPWMSPEED
- 51直流电机PWM测速程序keil编译C语言-51 DC Motor PWM Speed keil compile C language programs
synchronousmachine
- 多回路法在故障诊断有着广泛应用，改程序是基于C++用多回路法计算凸极同步电机参数的函数。-Multi-loop method is widely used in fault diagnosis, changes are based on C++ with multi-loop method to calculate parameters of a salient pole synchronous motor function.
bujindianjikongzhi
- 步进电机的控制，用C51编的，本人测试可用-Stepper motor control, with the C51 series, I test available. . .
HVI_JN338_R001_02
- 根据转矩转速测量仪传过来的数据实时绘出电机的转矩、转速、功率曲线图-Measuring torque and speed according to the data transfer over time draw motor torque, speed, power curve
motor
- 驱动步进电机，用的是光驱中拆下的电机， 大至都是差不多的了-Drive motor, using a drive motor removed from large to almost all of the
xiaochexunji
- msp430控制直流电机，包括左转弯，右转弯，直行，直退，TimberB用于速度控制。-msp430 DC motor control, including turning left, turn right, go straight, Zhitui, TimberB for speed control.
Ex027
- 一个主从系统的控制界面。主机可以控制电机转速，水温加热和超声波测距三个子系统。其中还包含一些小插件的源代码，对GDI，GUI的初步探讨有所帮助. 它同样具有USB的驱动的代码-A GUI of master-slave system. Master PC could control motor, heater and ultrasonic distance measurement system.It also provide a good introduction for the freshma
intellectual-car
- 简易智能迷宫小车的控制系统以STC89C52为核心，用一片L298N驱动两个减速电机。12V电源单独给电机供电，再用7805把12V电源降压至7V给单片机供电。小车的传感器模块感应壁障，并将壁障信号输入最小系统版，最小系统版根据程序设计的要求做出相应的判断送给电机驱动模块，让小车来实现前进、左转、右转、反转等基本功能。-Simple intelligent control system of the labyrinth car STC89C52 as the core, two geare
3
- 关于液晶12864，串口通信RS232，步进电机，数码管动态扫描，时钟程序，音乐兰花草的小程序，都是在CVI上开发的，好用。-On LCD 12864, serial communications, the RS232, stepper motors, digital tube dynamic scan clock program, small program of music orchids are developed on the CVI, easy to use.
Untitled
- 快速傅里叶分析，波形质量的分析,用于电机气隙磁密、反电动势波形等的分析-Fast Fourier analysis, waveform quality analysis used for the analysis of the motor air gap flux density, back-EMF waveform
gengzhong
- 点光源追踪，步进电机与MSP430，实现对电光源的追踪，可用于太阳能-Point source tracking, stepper motor and MSP430, to achieve the tracking of electric light, can be used for solar energy
electrical-machinery-acceleration
- 步进电机加速减速匀速演示，适合开始学51单片机的人学习一下。-Step-by-steps the electrical machinery acceleration deceleration uniform speed demonstration
bujindianji-kongzhi
- ATmega128 步进电机源程序，可用于控制步进电机的左右转及pwm的调节，控制电机的转速以及旋转方向-ATmega128
dianjitiaosu
- 用89c52和L298N电机驱动模块、LCD1602做的电机调速-89c52 and L298N motor drive modules, LCD1602 do motor speed
bujindianji
- 步进电机程序，可以实现正转，反转，停止等功能，亲测过，很好用-Stepper motor program, can achieve forward, reverse, stop, pro-test before, easy to use
bujin
- 步进电机控制程序，可以实现正转，反转，停止等功能，非常好用!-Stepper motor control procedures, can achieve forward, reverse, stop and other functions, very easy to use!
C8051F330
- 基于C8051F330对步进电机的控制，可以实现加速，减速等功能，程序非常好懂-For C8051F330 stepper motor control, acceleration, deceleration, and other functions can be achieved! ! !
capture-invert
- 有位置传感器无刷直流电机捕捉和换相程序，利用DSP发出PWM波-Capture of sensorless brushless DC motor commutation procedures, the use of the DSP PWM wave