搜索资源列表
一个非常好用的Autocad工具集
- ********************************************************* * AyungerStudio AutoCAD-Tools 更新日期: 2010.02.01 * ********************************************************* 这是本人近年来独自开发的一个AutoCAD修改工具集合，现与各位共享，主要包括： 1、 绘制类： 箭头、示坡线、锥坡线、剖断线、垂线、切线、等高线加
caiji_16C
- 用于MP411 AD转换卡,同时采集16路通道连续信号并显示,各通道可单独设置电压值等参数,最后可生成报表浏览结果,开发环境为C++Builder6.0,可用于学习AD卡设置,采集函数及信号数据处理-MP411 AD converter card used at the same time collecting 16-channel signal and a row shows that the channel can be individually set parameters such as
alarm-V3
- 本程序为检测16路输入45~65HZ的信号，并按每路状态输出各自想应路信号-This procedure for the detection of 16 of 45 ~ 65HZ input signal, and the way each state would like to output their signals should be
ofdm1
- 建立正交频分多路复用(OFDM)系统调制器的仿真模型，并编程给出具有K=10个子信道、符号区间T=100s、采用16点QAM信号时，OFDM系统调制器的输出信号。-The establishment of orthogonal frequency division multiplexing (OFDM) system, the simulation model of the modulator and the program is given with K = 10 Ge sub-channel
fun3
- 16路开关模块软面板设计 用cvi 实现-16 switch modules to achieve the soft-panel design with cvi
4-20MAprogra
- 16路的4-20mA，多通道扫描电流采集的程序-4-20mA current acquisition program
LPLD_ADC
- 此程序段是基于K60单片机的ADC采集的程序，其完成了4路16位ADC数据采集，对高精度、高速率ADC采样有很大的用处。-This block is based the K60 MCU ADC acquisition program, to complete a 4-channel 16-bit ADC data acquisition, high-precision, high-speed ADC sampling is very useful.
YGZ_ADC
- 此程序段是基于K60单片机的ADC采集的程序，其完成了4路16位ADC数据采集，对高精度、高速率ADC采样有很大的用处。-This block is based the K60 MCU ADC acquisition program, to complete a 4-channel 16-bit ADC data acquisition, high-precision, high-speed ADC sampling is very useful.
HI3521DMEB-VER.A
- 海思3521处理器，16路CIF DVR原理图，参考设计-Hass 3521 processor, 16-channel CIF DVR schematics, reference design
Qam16
- 16 进制的正交振幅调制是一种振幅相位联合键控信号。16QAM 的产生有 2 种方法： （1）正交调幅法，它是有 2 路正交的四电平振幅键控信号叠加而成； （2）复合相移法：它是用 2 路独立的四相位移相键控信号叠加而成。-Quadrature amplitude modulation is a hex key signal amplitude and phase combined. 16QAM produce two kinds of methods: (1) quadrature a
VM6000
- 利用QT写的可以实现对不同地点摄像头进行监控，可以在1路、4路、8路、16路，全屏之间进行切换，摄像头是每个分配一个ip。-QT can use to write to different locations to monitor the camera, you can switch between the 1-way, 4-way, 8-way, 16-way, full-screen, each camera is assigned a ip.
sidulinkmode
- 采用THP预编码QR算法的simulink仿真链路,有16QAM和QPSK两种调制方式-With THP precoding simulink link of QR algorithm, there are 16 qam and QPSK modulation mode
db99I_3
- 基于c8051f310CPU，灵活控制16路继电器实现各路音响输出。控制端为PC机，MODBUS协议(Based on c8051f310CPU, flexible control of the 16 way relay, to achieve all kinds of audio output)
ADCS
- 支持16路ADC采集，STM32单片机。采集后结果通过串口显示。(Support 16 way ADC acquisition, STM32 microcontroller. After collection, the result is displayed through the serial port.)
16路舵机控制板资料1.2
- 16路舵机模块，内有芯片介绍，原理图介绍，编程介绍(16 steering gear module, inside chip introduction, principle diagram introduction, programming introduction)
6337194
- 采用THP预编码QR算法的simulink仿真链路,有16QAM和QPSK两种调制方式(With THP precoding simulink link of QR algorithm, there are 16 qam and QPSK modulation mode)
Qam_modulation
- matlab 16 qam 调制的代码。将调制信号先分成IQ两路，再进行信号的调试。(Matlab 16 QAM modulation code. The modulation signal is first divided into two IQ paths, and then the signal is debugged.)
TLV5610-数采板程序 PDF
- 一份16位8路DAC模块的测试程序，所用芯片为TLV5610(16 bit eight - way DAC module test program)
1616
- 16路数字量模块通断控制程序，使用MODBUS通讯协议(16 way digital module block off)
MCP23017+IIC接口16路IO扩展模块资料v1.1
- 模块为 I2C 接口的 16 路 IO 扩展模块，采用 MicroChip 的 MCP23017 芯片。芯片功能完备，每个 IO 可 任意配置为输入或输出，可设置使用上拉电阻。并且配置为输入的 IO 都可以启用中断功能。IO 接口驱动 能力强，灌电流、拉电流可达 25mA。(Module for the I2C interface of the 16-way IO expansion module, using Microchip MCP23017 chip. The chip funct