搜索资源列表
SPI
- stm32f103 SPI 驱动代码 ，可以直接 使用 -OK
atmega8
- nrf24l01和ATmega8之间通信协议，刚试验成功，可以简单的收发数据，模拟SPI口-nrf24l01 and communication protocols between ATmega8 just successfully tested, you can simply send and receive data, simulation SPI port
spi
- IAR 环境下MEGA16的SPI驱动程序，包括软件模拟和硬件SPI-IAR environment MEGA16 the SPI driver, including software simulation and hardware SPI
SPI
- studio gcc 环境下模拟实现过的spi程序，绝对适用，-studio gcc simulated environment to achieve off spi procedures, the absolute application of
isd4004
- 语音芯片ISD4004的驱动源码，采用IO模拟SPI总线控制-ISD4004 voice chip, the driver source code, using IO simulation SPI bus control
TC72
- TC72的spi采集温度，用io口模拟，移植性好-TC72 the spi acquisition temperature, io port simulation, portability
AD7714-C
- AD7714驱动代码 采用LPC1751做为CPU平台，标准的SPI通信和IO模拟SPI通信-AD7714 DRIVERS LPC1751 CPU SPI Interface
SD
- 基于stc12c5060s2的自带SPI控制器的SD卡读写程序，直接使用的SPI总线，不是通过IO模拟的-Stc12c5060s2 with a SPI controller based on the SD card reader program, the direct use of SPI bus, not by IO simulation
Touchscreen
- 以总线方式操作控制TFT彩色液晶,模拟SPI控制触摸屏，将按下的点显示在TFT 2.4寸液晶上。因此，可以用此程序来在屏上画图案。由于触摸屏在采集时每次采集的值都有误差，这也是使用触摸屏较为麻烦的地方，通过查资料，发现 目前处理此问题主要通过软件算法实现，并且功能稳定的往往算法想法复杂，本程序采用简单的算法来 实现：当某一点按下后，在保持不放开的前提下，采集7个数据，并对数据进行升序排列，取中间3个数据 作为有效数据，并将平均值作为按下后的X，Y坐标。-Bus operation
SPI
- XN12Lxxx模拟SPI， 根据目前流行的SPI FLash编写的参考代码，可以方便人员缩短开发时间-The XN12Lxxx analog SPI, based on the currently popular SPI FLash written reference code, you can easily shorten development time
C-SHARP_USB_ADC_Test
- 在C#平台调用USB-I2C适配器或者USB-SPI适配器的二次编程接口函数实现ADC（模数转换）功能，USB-SPI适配器和USB-I2C适配器有8路、12bit、采样频率为1M的ADC，适配器采用3.3V参考电压，利用适配器的ADC功能可以测量0到3.3V之间的模拟电压信号。-Calling adapter or USB-I2C adapter USB-SPI in C# programming interface functions to achieve the secondary pla
ATT7022C
- 单片机IO口模拟SPI时序，控制ATT7022C，SPI的最大速度是2M。-SPI microcontroller simulation
24l01_demo
- nrf24L01底层驱动,使用单片机IO模拟SPI,简单易行,很容易移植,文件是针对MSP430而写,我也已移植51,STM8等单片机中运行.-nrf24L01 underlying driver, use microcontroller IO simulation SPI, simple, very easy to transplant, the file is written for MSP430, I have also been transplanted 51, STM8 microco
MCU-simulate-SPI--Read-Write-m25p80
- 单片机模拟SPI程序读写m25p80 C语言程序，值得借鉴-Single chip simulation SPI program to read and write C m25p80 language program, it is worth learning
leonkk1020.X
- io口模拟spi，ADC采样模块，串口模块接收命令(io port analog spi, adc sampling module, serial module two receive commands)
13898359STM32-AD7705
- 用C语言编程对模拟量进行采集，单片机采用STM32，用SPI协议去读写AD7705，精度高，稳定性好，适合前端模拟量采集。(C language programming is used to collect analog data, MCU uses STM32, and SPI protocol is used to read and write AD7705. It has high precision, good stability, and is suitable for front-e
ADF4153
- 已验证好的应用函数，采用模拟IO方式，也可以作为SPI模拟初学者参考(The application function has been verified, using analog IO mode, can also be used as SPI simulation beginners reference)
【02】火牛_LCD Touch(2014.07.10)
- 模拟SPI驱动XTP2046，火车开发板提供(Analog SPI driver XTP2046)
main
- STM32模拟SPI接口驱动HT1621芯片，修入接口引脚直接可用(The STM32 analog SPI interface drives the HT1621 chip, and the interface pin is directly available.)
STC-7705
- 51单片机模拟SPI TM7705 程序，修改引脚可直接用(stc,mcu ang spi read TM7705)