搜索资源列表
aaa
- 本文介绍了两相四拍混合式步进电机的工作原理及其磁网络模型，推 导了步进电机的动态方程。分析了两种细分驱动方法:等电流法和电流 矢量法恒幅均匀旋转法，提出了基于单片机控制的PWM电流矢量恒幅 均匀旋转的细分驱动技术，实现了步进电机32细分驱动。-so much,so nice.
aaa
- 在数控原代码开发过程中提出了步进电机正反转控制的实现方法,并根据此方法,给出了其相应的实现程序。 -very good.
s3c2410
- s3c2410 步进电机的驱动 （毕业设计）-s3c2410 stepper motor drive (graduation project)
S3C2440_pwm
- S3C2440的PWM输出驱动,可以输出频率可调的PWM方波以控制步进电机-The S3C2440 PWM output drive, the PWM square wave can be output frequency is adjustable to control the stepper motor
motor2
- 电机驱动。linux下的arm编程电机正转翻转等功能的实现-Motor drive. arm programming under linux
STEPMOTOR_L298DRVtest
- 用于L298N的交流电机驱动，本代码用于步进电机正传两相八拍的程序。-For L298N AC motor drive, the code for stepper motor True Story of two-phase eight-beat program.
STEPMOTOR_L298DRVtest
- 用于L298N驱动步进电机，本代码用于步进电机反转两相四拍。-For L298N drive stepper motor, and the code for two-phase stepper motor reversal shot.
STEPMOTOR_L298DRVtest
- 用于L298N驱动控制步进电机，本代码是其中的两项四拍程序。-For L298N drive control stepper motor, the code is one of the two four-beat program.
motor2.0
- 基于linux rethad gec2440（ARM9）板卡开发的步进电机驱动，可以控释电机正反转，停止。-Based linux rethad gec2440 (ARM9) stepper motor driver board development, controlled-release motor reversing, stop.
YL-19
- 用于L298N驱动对电机的控制资料，包括其原理图和芯片资料等。-For L298N driver of the motor control information, including schematic and chip data.
DC-motor
- 用于L298N对直流电机的全部控制代码，包括正反转和速度的控制。-For L298N DC motor control code, including reversing and speed control.
EW-ARM-s3c2410-mr-control
- 基于EW-ARM 开发s3c2410 电机转动控制-Based on EW-ARM development S3C2410 motor rotation control
dc-engine-control
- s3c2410 直流电机控制实验,ARM A9开发-s3c2410 DC motor control experiment, ARM A9 development
motor
- mini2440的两路pwm驱动程序，可以控制直流电机的正反转和转速-mini2440 two PWM driver, you can control the the positive DC motor and speed
09_dcmotor
- arm2410中控制直流电机的程序，电机正反转-the arm2410 DC motor control procedures, motor reversing
MOTOR
- 嵌入式实验的电机控制程序，在linux下编译，在a8rp实验台上运行，A8RP是ARM系统。-Embedded experimental motor control procedures, compile under linux, run a8rp experimental stage, A8RP ARM systems.
rightMotorContr.c
- MicroMouse618上的右步进电机驱动时序优化程序，2013版本-On the right MicroMouse618 stepper motor driver timing optimization program, 2013 version
lpl_stepper
- linux下基于S3C2440开发的步进电机驱动，一根信号线控制HB202M细分器即可实现步进电机速度和方向的控制-linux based S3C2440 development of stepper motor drive, a signal line control HB202M subdivision stepper motor controller can achieve the control of speed and direction
08Stepper_motor_experiment
- 使用操作系统控制电机正转和反转，本实验新颖别致，适用于初学者进行电机控制实验-Using the operating system controls the motor forward and inversion, this study is novel and chic, suitable for beginners to motor control experiment
drivate
- 这是2410控制步进电机的驱动程序，仅供参考。-This is the driver it is trying to control a stepper motor