搜索资源列表
lcd
- 基于linux2.6.12和s3c2440的LCD应用程序，可以根据库数据打印相应的汉字，已测试通过-S3c2440 based linux2.6.12 and the LCD application data can be printed according to the corresponding Chinese character library, have been tested
CAN_MCP2515
- 该程序为基于s3c2440的CAN控制芯片MCP2515的裸机演示程序（其中已包含spi总线驱动）-The program is based on the the s3c2440 bare metal of the MCP2515 CAN controller chip demo program (which contain spi bus driver)
ADCtest
- 本程序为基于s3c2440的A/D转换及触摸屏测试裸机程序，可以实现对一路A/D转换或触摸屏电路的测试。-This program is based s3c2440 A/D conversion and the touch screen test bare metal program, you can achieve all the way to the A/D conversion or touch screen circuit test.
mcpcan
- S3c2440 can总线底层驱动程序代码-S3c2440 can bus the underlying driver code
S3C2440_pwm
- S3C2440的PWM输出驱动,可以输出频率可调的PWM方波以控制步进电机-The S3C2440 PWM output drive, the PWM square wave can be output frequency is adjustable to control the stepper motor
makefile
- 该文档是s3c2440芯片的spi1接口在linux系统中驱动模块的makefile文件。可以直接在文档目录下执行make命令。-this file is the makefile of the driver of s3c2440 s spi interface。you can exercise the command make in the same pathetic。
CAN
- 基于S3C2440的CAN驱动程序，裸机下跑，了解ARM9的CAN工作机制-Based on S3C2440 CAN driver bare metal run, understanding the ARM9 CAN working mechanism
CAN_RX1
- 基于S3C2440的CAN驱动程序，裸机下跑，了解ARM9的CAN工作机制-Based on S3C2440 CAN driver bare metal run, understanding the ARM9 CAN working mechanism
vivi_2440
- 此vivi的源码是针对64M（小页）NANDFLASH的s3c2440开发板，编译出的程序能在64MNANDFLASH上运行-Vivi source for the 64M (page) NANDFLASH s3c2440 development board, compile the program can be run in 64MNANDFLASH
hardware
- 这是基于S3C2440的底层裸机驱动代码，对于初学ARM9的朋友很有帮助。希望大家能尽快掌握这些知识。-This code is based on the S3C2440 the underlying bare metal drive, helpful beginner ARM9 friends. I hope that we can master this knowledge as soon as possible.
SPI2UART
- 开发环境Ubuntu10.10 内核源代码版本linux2.6.32.2 交叉编译环境版本V4.4.3 驱动函数说明： 该代码将S3C2440的SPI口连接SC16IS752，扩展为2路串口。代码分2部分，分别Make后生成2个.ko文件，分别加载即可使用。 本代码项目实用，可参考。-Development environment Ubuntu10.10 Kernel source code version linux2.6.32.2 Cross-compiler
UART2
- 开发环境Ubuntu10.10 内核源代码版本linux2.6.32.2 交叉编译环境版本V4.4.3 驱动函数说明： 该代码是S3C2440的UART2口驱动。半双工通讯，可在加载代码时修改波特率。 本代码项目实用，可参考。-Development environment Ubuntu10.10 Kernel source code version linux2.6.32.2 Cross-compiler environment version V4.4.3
lpl_stepper
- linux下基于S3C2440开发的步进电机驱动，一根信号线控制HB202M细分器即可实现步进电机速度和方向的控制-linux based S3C2440 development of stepper motor drive, a signal line control HB202M subdivision stepper motor controller can achieve the control of speed and direction
basic
- 是s3c2440的基础实验代码，是完整的实验代码，能够直接运行-Is based s3c2440 experimental code, is a complete experimental code that can be run directly
s3c2440_linux_pwm
- 基于mini2440开发板的linux下s3c2440的pwm驱动程序，实际测试验证，程序可正常运行，方便移植到其他开发平台。-Under mini2440 development board based on linux s3c2440 pwm driver, actual test, the program can run normally, easily ported to other development platforms.
rootfs.tar
- 自己实现的yaffs2文件系统，可以直接在开发板上使用。linux移植需要的通用文件系统。基于s3c2440-Their implementation yaffs2 file system that can be used directly in the development board. linux transplant requires a common file system. Based on s3c2440
testdrv
- 这是一个fl2440 按键中断驱动文件，arm9（s3c2440开发平台），按下开发板按钮开关1，便可测试，通过cat /proc/interrupts 命令在include/arch/irqs.h 可查证。-This is a key interrupt-driven file fl2440, arm9 (s3c2440 development platform), press the button to switch a development board, can be tested by
uCos2-20140826
- s3c2440 开发板的ucos II 测试代码，经测试可以使用。-s3c2440 development board ucos II test code, the test can be used.
vs_10xx
- VS1053在linux下的驱动 采用netlink实现 运行在S3C2440平台上， 可移植到其它平台 完全自主原创-Linux driver for vs1053 to play mp3 files. Implemented by netlink. Successfully run on S3C2440, and can be port to other platform.
my-wm8976
- 基于S3C2440的声卡驱动程序，声卡芯片是wm8976，已经调试成功，可以播放wav文件，也可以录音-S3C2440-based sound card drivers, sound chip is wm8976, debugging has been successful, you can play wav file, you can also record