搜索资源列表
pm
- 不同方式2410开发板上led的4个灯的亮法-2410 development board in different ways the four lights led light method
led
- s3c2410ARM板上的led驱动程序 用它可以驱动led灯的变化-s3c2410ARM panel LED driver can drive led light changes
s5pc100
- 利用平台设备机制，对s5pc100实现按键对Led灯的控制，按下点亮，松开熄灭-Use platform equipment mechanism to realize s5pc100 buttons on the control of Led lights, press the light, loosen put out
leds-gpio
- 控制led灯的驱动程序，也就是流水灯，程序中有4个led灯，依次按照先后顺序亮与灭-Control driver led lights, light water, 4 led lights in the program, followed in accordance with the sequence of bright and off
ARM-LED
- 点亮熄灭一个LED灯，点亮熄灭所有的LED灯-Light turns off an LED light turns off all the LED lights
drv_dv_platform_gpio_a
- GPIO实现LED驱动， 把LED等一个一个的点亮-GPIO LED driver, LED and other light
key-and-led
- stm32的可用驱动模板，通过简单的按键控制流水灯来实现-the stm32 available driver templates, through the simple push-button control of light water
bitctl
- linux下面2.6.24版本内核的位控制的驱动代码，实现了led发光二级管的控制。-bit linux 2.6.24 version kernel driver code control, led light emitting diode control.
from51-to-arm-and-led-test
- 从51单片机到arm的入门教程，以及简单的流水灯测试实验的代码，对于初学者比较有帮助-51 microcontroller arm introductory tutorial, as well as the simple code of the light water testing laboratories, more help for beginners
led_analog_traffic_light
- /** *本程序目的为控制LED灯模拟红绿灯 * 具体：Edkit-8试验箱中可以介入4个LED灯，但我们只用其中的3只 * 规定第1只表示红灯，每次亮20秒 * 规定第2只表示黄灯，每次亮5秒 * 规定第3只表示绿灯，每次亮20秒 *开始时红灯先亮，然后黄灯、绿灯依次亮。循环反复 *每次灯切换时会有3秒的闪烁时间 * * *gcc -o led_analog_traffic_light led_analog_traffic_light
8-test-light
- linux编写的pwm的驱动，可以用pwm控制led暗亮-the linux written PWM drive, you can use pwm control led dark light
pmd
- 跑马灯 ，使LED灯发光倍率成倍数增加，通过改变计数器初值，初值设置要一定大，小于-Marquee, the LED light magnification multiples increased by changing the counter initial value, the initial value is set to a certain large, less than 99 000
s3c6410_leds
- linux s3c6410 LED 将为我闪烁 控制发光二极管-LED light-emitting diode will blink control me
LED301
- LINUX3.0.1下的飞凌OK6410A开发板的LED的驱动程序以及流水灯用户程序-LINUX3.0.1 Feiling OK6410A under development board LED drivers and light water user program
LED2
- MINI6410开发板上的LED驱动GPM接口，看也控制4盏LED的亮按-MINI6410 development board on the LED driver GPM interface, see also control four LED light in
led
- 驱动程序，在ARM linux上控制led亮和灭-control led light
watchdog
- 基于samsung6410开发板的watchdog裸板驱动，通过控制watchdog，喂狗，产生中断，控制led的亮灭-Drive watchdog bare board based on the samsung6410 development board, by controlling the watchdog, feed the dog, interrupt, control LED light off
smart210_led_driver
- 1.首先加载驱动 insmod smart210_led.ko 2.open( /dev/设备文件名 ,O_RDWR) 3.用ioctl(fd,LED_ON,value) 操作led 第二个参数可以为LED_ON,LED_OFF,LED_ALL 当为LED_ON时第三个参数只能取值1-4 （说明点亮固定led，若第三个参数为3表示点亮第三个led） 当为LED_OFF时第三个参数只能取值1-4 （说明熄灭固定led，若第三个参数为3表示熄灭第三个led） 当为LED
LED
- 点亮P1口的一个LED灯 该程序是单片机学习中最简单最基础的， 通过程序了解如何控制端口的高低电平-A leds light up P1 mouth The program is the basis of a microcontroller learning one of the most simple, Through the application to know how to control the high and low level of port
Fading-fast-flowing-water-light
- LED流水灯 的控制方法。 我们用了变量j,来控制流水灯的速度。 12个LED不停的依次闪烁，每闪烁一圈，闪烁的速度加快一点， 当转了8圈后，流水灯的速度达到最快。 -Fading fast flowing water light