搜索资源列表
DSP的定时器中断汇编程序
- 基于TMS320VC5402 DSP平台的定时器中断程序，使用的汇编语言，在CCS里调试通过。-Based on TMS320VC5402 the DSP platform timer interrupt program,with assembly language, debugs in CCS passes
44b0中断程序1
- 这是三星公司的arm7 s3c44b0x芯片的所有外设中断程序，都是用标准c语言编写的-This is Samsung's chip ARM7 s3c44b0x all peripherals interruption procedures, standards are used to prepare the language c
ARM9的中断处理技术及其在Windows CE下实现的研究
- 文中介绍ARM9系列嵌入式微处理器的中断体系结构，论述Windows CE．net的中断处理 过程，并在此基础上给出基于EP9301微处理器的Windows CE．net 4．2下进行中断程序开发的实 例。
UART_INT 串口中断程序
- 串口中断程序：S3C2440A芯片，S3C920T内核-Serial interrupt program: S3C2440A chip, S3C920T kernel
zhongduan
- 自己写的 51单片机的中断程序，用c语言写的-Single-chip microcomputer 51 to write their own interrupt procedures, the use of c language
ini
- 这是飞思卡尔mc9s12xs128b CPU的一个中断程序 并且可以直接调用-This is mc9s12xs128b CPU Freescale an interruption of the procedure and can direct calls
key_interupt
- 键盘中断程序，通过DNW的串口或超级终端的串口都可以实现键盘的中断。-Keyboard interrupt procedures DNW HyperTerminal serial port or serial port can be the realization of the keyboard interrupt.
freescale-ep100-ECT-capture-interrupt
- freescale ep100 ECT捕捉中断程序，按程序中代码初始化即可启动使用捕捉中断，代码已经经过调试。-freescale ep100 ECT capture interrupt program, according to the procedure in the initialization code to activate the use of capture interrupt, the code had already been debugging.
freescale-Ep100ECT-capture-interrupt
- freescale ect 捕获中断程序，程序已经经过调试，成功。-freescale ect capture interrupt program, the program had already been debugging and successfully.
key_driver0005.tar
- s3c2440 键盘驱动，使用键盘中断程序演示tasklet和工作队列-s3c2440 keyboard driver, using the keyboard interrupt program presentation and the work queue tasklet
S3C2410-init
- 基于ARM9芯片S3C2410异常中断程序设计。验证的代码详细分析了基于ARM嵌入式系统的异常处理流程。然后阐明关键字“-irq”的作用，设计出中断处理函数。最后，通过设置中断控制寄存器，设计外部中断EINT3的初始化程序，并给出主程序流程图。实践证明程序运行稳定可靠。-S3C2410 ARM9-based chip exception interrupt programming. Detailed analysis of the code verification of embedded sy
stm32f103串口2中断程序
- stm32f103串口2中断程序, 完整keil4工程 stm32f103串口2中断程序，完整keil4工程 stm32f103串口2中断程序，完整keil4工程 stm32f103串口2中断程序，完整keil4工程
51基本程序
- 关于51单片机的外部中断程序，主要用到两个中断。(There are two main interrupts on the external interrupt procedure of 51 MCU.)
实验8 定时器中断实验
- STM32的定时器中断程序，亲测可用。内有详细注释和说明文档，很好的参考资料。(STM32 timer interrupt program, pro test available. There are detailed notes and documentation, good references.)
STM32F107外部中断程序
- 按键触发STM32的GPIO中断，点亮LED(Keystroke triggers GPIO interrupts)
STM32定时器中断程序
- 本源代码为讲解基于STM32的定时器中断程序，通过定时器TIM3产生间隔1秒钟一次的中断，在中断中控制LED发光二极管，每次中断都使发光二极管状态取反(This source code is explained based on the STM32 timer interrupt program, through the timer TIM3 interrupt an interval of 1 second, in the interrupt control LED light-emittin
STM32外部中断程序
- 本源代码为基于STM32的外部中断程序，需要关注的点是相应端口时钟配置、管脚初始化配置和中断配置(The source code is an external interrupt program based on STM32, and the point to focus on is the corresponding port clock configuration, pin initialization configuration, and interrupt configuration.)
定时中断程序
- msp430定时器中断程序例程,通过定时器A，设定时间为1S触发一次中断。(MSP430 timer interrupt routine routine)
STM32 外部中断
- 中断程序，STM32F103系列的源码，实现简单的中断功能(Interrupt program, STM32F103 series of source code, to achieve a simple interrupt function)
N76E003串口0、串口1中断程序模板
- N76E003串口中断程序模板，实现串口中断接收和发送(N76e003 serial port interrupt program template to realize serial port interrupt receiving and sending)