搜索资源列表
VCProgram
- 本人用VC6.0开发的单片机通过串口与PC机通信的上位机,通信协议在说明文档中已经写出,用户在单片机上编写串口函数时按照通信协议,便可以很方便通过此软件与PC机通信.-err
BT1800-1_bluetooth_module
- 超远距离蓝牙模块,模块在空旷场所通信距离达到1800米,广泛得被国防科大、武汉大学等众多科研项目配套使用。 模块可以是用在USB蓝牙,也可以用在串口数据无线传输。其串口模块成对使用,对于外界开发来说,其相当于一根蓝牙串口线。您无需考虑繁琐的蓝牙协议,您只需要简单的配置波特率、主从模式,就可以为您的系统增加一个强大的蓝牙功能,您只需要用您的单片机通过串口发送数据就能实现蓝牙通信。蓝牙模块 远距离蓝牙 工业蓝牙 医疗蓝牙 串口蓝牙 USB蓝牙 性能稳定 性价比高 心电 煤矿 深圳蓝色飞舞科
chuankou
- MSP430异步串口程序,实现简单的协议,既可以用于单片机之间通信,也可以用于单片机与PC机通信。-MSP430 UART procedures, to achieve a simple agreement, both can be used for communication between the single-chip, single-chip can also be used for communication with the PC.
80C51_1
- 1.异步通信软件模拟2.基于RS-232的串口通信3.基于RS-485的多机通信4. I2C总线协议的软件实现5. SPI总线在单片机系统中的实现6.-wire-1. Asynchronous communication software simulation 2. Based on the RS-232 serial communication 3. Based on the RS-485 Multi-machine communication 4. I2C bus protocol soft
shizhong
- 如果是用pc的串口传输数据就好办了,可以安装一个串口监视工具(如AccessPort)。电脑串口一般是2、3、5三根线通讯,2是txd,3是rxd,5是GND,但是电脑的逻辑电平与单片机的逻辑电平不同,具体看串口通信协议,网上很容易搜到。 IIC总线上的数据可以通过示波器查看,两个探头,一个连接clk,另一个连接sda,IIC通信时可以观察到传输的数据。 -If you are using pc' s serial port to transfer data much easier t
13-45
- 本程序能够完成的功能是,自动或手动测温,读取配置寄存器,温度下限寄存器,温度上限寄存器,设定温度上限及下限,当温度到达预定的温度的时候报警。所有的读取操作都可以在数码管上显示。其中,温度的上限通过计算机用串口通信协议传输给FPGA内部寄存器然后按动开关写入。同时,本程序还驱动了一个直流电机,温度高的时候电机转速高,温度低的时候转速降低直至停转。数码管可以实时显示电机转速,2秒刷新一次。数码管的显示可以在显示的温度、寄存器值和直流电机转速间切换,切换通过串口进行,计算机发00H时切换到温度及寄存器
138-UART
- 介绍TI 138芯片的串口通信协议及寄存器配置-Introduction TI 138 chip serial communication protocol and the configuration register
USART_AT93C46
- PIC16F877实现串口通信协议数据包通信,同时能通过窗口上位机对AT9346进行读写功能。-PIC16F877 Serial communication protocol packet communication, while the host computer through the window to read and write capabilities of the AT9346.
51danpianji_chuankou_tongxin_xieyi
- 51单片机的串行通信协议的实现 串口通信协议-51 single-chip serial communication protocol implementation
UART
- UART串口通信协议的verilog代码-Verilog code of UART serial communication protocol
s24_uart
- 这是一个串口通信协议,有详细的说明,欢迎下载!-This a code of uart in verilog ,describled in detail,welcome to download!
1
- 利用C语言编写的51单片机的串口通信协议实现-51 single-chip serial communication protocol using C language
UART51
- 51单片机串口通信协议制定,可以自己定义串口通信协议,用于组建控制网络-51 single-chip serial communication protocol to develop, can define your own serial communication protocol for the formation of the control network
xiaoxuehui.tar
- 该代码是基于QT的串口通信. 该串口通信可以设这波特率,数据位等一些设置. 主要是用于嵌入式方面的串口通信协议.-The code is based on the QT serial communication of the serial communication can set some settings for baud rate, data bits. Mainly for embedded serial communication protocol.
UARTtesting
- 基于mega128的uart串口通信协议已经验证完毕,调试通过-Mega128 uart serial communication protocol validation is completed, through debugging
232
- RS232串口通信协议的学习,对于初学者有挺好的帮助-be useful to everyone
USART
- STM32串口通信协议,可根据需求更改协议,简单已改-STM32 serial communication protocol, according to the demand to change the protocol, a simple
I2C_51C-Source-Code
- Camera常用串口通信协议之I2C的51 C语言源代码-Camera of the I2C serial communication protocol commonly used in the 51 C-language source code
FPGA_UART
- FPGA实现UART串口通信协议 采用VHDL语言,顶层文件采用原理图的方式,简洁直观-FPGA Implementation of UART serial communication protocol