搜索资源列表
uart-verilog-vhdl
- 拿verilog和vhdl编写的串口通信代码(可综合)-with vhdl and verilog prepared by the serial communication code (synthesis)
TBA-8246C
- 用c语言编写的单片机程序，能够实现多串口通信及485通信，提供给大家分享。-c language used in the preparation of SCM procedures can achieve multi-485 serial communications and communications, to share with you all.
testNode
- 该工程是由IAR Embedded Workbench开发，完成的功能是由DS1820采集温度数据，通过单总线方式发送到MSP430中，再由处理器通过串口通信将数据发送到PC机中进行记录．-the project by the IAR Embedded Workbench development, The function is to be completed by the DS1820 temperature data collected through the single bus disp
seilralcomunication
- 单片机双机,多机串口通信 通过编译运行 供大家参考-SCM - machine, multi-machine serial communications through the compiler running for your consideration
5416UART
- 基于ti公司54x系列DSP的串口通讯程序，本程序可以实现dsp与PC的实时通讯，本人已经验证过，不过你的板子上要使用16C550串口通信模块，它占用DSP的一个端口，用来实现与PC的通信，程序的开始是对它的内部寄存器进行定义。-Series DSP chip serial communication procedures, The dsp procedures can be achieved with the PC real-time communication, I have tested,
fet440_uart01_09600
- MSP430系列单片机 UART串口通信程序-MSP430 MCU UART serial communication program
connmc_serial
- wince 5.0 通信在wince5.0上测试通过，可以用于串口通信-wince 5.0 Communication in wince5.0 through testing, can be used for serial communication
SUART
- 基于飞利浦公司ARM7处理器，LPC2132。用定时器和IO口做的串口通信程序源代码-based Philips ARM7 processor, LPC2132. IO with a timer and I do serial communication program source code
nios_uart
- 基于Nios II的串口通信，在quartus的开发环境中进行的实验-based Nios II Serial Communication in quartus development environment for the conduct of the experiment
uCOS-II_uart_yingyong
- ucos下的串口通信例子，cpu为LPC2210-OUT of serial communication example, cpu for the LPC2210
serialport_for_51
- 优盘进行串口通信源代码专门写来为arm,51与优盘进行串口通信的东东, 代码短小精悍,高度规范。可以在电脑上象操作 DOS一样仿真优盘的开发。-Youpan for serial communication source code written specifically for the arm, and 51 Youpan Serial Communication for Eastern, code small and highly standardized. Be on the comput
uartrw
- linux 串口通信程序,可以设置波特率等,然后通信-linux serial communication program, set baud rate, then communication
44B0UARTFIFO
- 44B0 ARM7处理器的串口通信程序，包括初始化和硬件驱动。-44B0 ARM7 processor serial communication procedures, including drivers and hardware initialization.
DSPMotor0528
- 原创推荐－电动机控制上位机监控程序（串口通信，界面采用了示波器样式，非常好！）-original recommendation-Motor Control PC monitoring program (serial communication interface used oscilloscope pattern, Very good!)
c51com
- c51用串口通信源码,包括调试 1.发送：向总线上发命令 2.接收：从总线接收命令，并分析是地址还是数据。 3.定时发送：从内存中取数并向主机发送.-decoder serial communication with the source code, including a debugger. Send : Bus made to order two. Acceptance : Bus from receiving orders and analysis of data or add
PROGRAMOF430UART
- 这个程序需要在430的IAR开发环境下运行，是关于430串口通信的程序。-the procedures needed in the 430 IAR development environment running on 430 serial communication procedure.
dsp_tl16c550
- dsp5416与tl16c550实现并口转串口通信程序-dsp5416 with tl16c550 achieve Parallel to Serial Communication Program
AT91SAM7X256-USART
- 在AT91SAM7X256的开发板上实现 串口通信-AT91SAM7X256 in the development of Serial Communication board
MCU_Practice
- 常用单片机程序范例代码，跑马灯、液晶显示，串口通信等常用范例-SCM procedures commonly used example code Bomadeng, LCD, serial communications, and other examples of commonly used
89c2051RS232
- Commulication Between 89C2051 and PC by RS232 用51的口线模拟串口通信-Commulication Between 89C2051 and PC by RS 232 with 51 of them simulated serial communication lines