搜索资源列表
C8051_DA_test
- 摘 要： 本文件是C8051单片机DA测试实验程序；使用外部22.1184MHz晶振. 功能：定义 A ~ F 为功能键。 按\"A\" 键，输出250HZ的方波，按\"B\" 键，输出250HZ的正弦波形，按\"C\" 键，输出250HZ的三角波， 按\"D\" 键，输出250HZ的锯齿波。用示波器在J6（DAC0）观测结果，使用串口观测按键信息。-Abstract : This document is C8051 MCU DA laboratory procedures; us
DSPMotor0528
- 原创推荐－电动机控制上位机监控程序（串口通信，界面采用了示波器样式，非常好！）-original recommendation-Motor Control PC monitoring program (serial communication interface used oscilloscope pattern, Very good!)
Serial_osiligater.rar
- 通过串口实现数据采集和显示，可以充当简易示波器使用，对于嵌入式开发具有一定的帮助。,Through the serial port data acquisition and display, can act as simple to use the oscilloscope for embedded development with some help.
msp430f149monichuanku
- 这是在TI网站上下的例程，绝对可用， P2.2,p2.3，在示波器上调试，调BitTime可以调节脉冲宽度，就可以调节波特率了，模拟串口发送一个字节需要发10位，起始位＋8位有效数据＋停止位，二真实串口不用发起始和停止位，因为缓冲区已经将他们加上了-This is a site from top to bottom in TI routines, absolutely available, P2.2, p2.3, in oscilloscope debug, tune BitTime can
MCU_MATLAB_oscillograph
- 使用ME300B开发板通过51单片机读取AD数据并通过串口将数据上传到PC，再使用MATLAB作图，实现简单的示波器功能-ME300B development board through the use of single-chip microcomputer 51 to read through the serial data and AD data uploaded to the PC, re-use MATLAB mapping to achieve a simple oscillosco
ScopeApi
- 通过串口读取示波器数据的程序，可以设置电压采样和频率采样-Oscilloscope data through the serial port to read the procedures, you can set the frequency of sampling and sample voltage
scope
- 数字示波器的源代码，串口发送，C语言描述-The source code of the digital oscilloscope
12
- 基于PC机串口进行数据采集的低频虚拟示波器程序-visual basic visual basic visual basic
extend
- MSP430 的程序，可以进行电压采集并通过串口与另一个单片机进行串行通信，另一台单片机将波形显示在示波器上-MSP430 process, voltage can be collected and microcontroller through the serial port with another serial communication, the other single chip waveform displayed on the oscilloscope
Serial_Oscilloscope_MSP430F149
- 用MSP430F149做的一个示波器，用Timer A定时触发AD转换，串口发送给电脑，最高采样频率100ksps左右，LABVIEW的visa接受和显示波形并可以控制时间轴和波形放大轴。-oscilloscope with MSP430F149 , starting with Timer A to trigger AD converter, send to the computer with RS232, the maximum sampling frequency 100ksps aroun
MultiDAQ
- LabVIEW STM32103 VISA 串口示波器 6路AD采样 2路PWM输出 DIO 数字输入输出-LabVIEW STM32103 VISA Serial communication 2PWM out DIO Wavefrom
xs128_Serial_Digital_Scope
- 串口示波器 XS128测试程序，可显示四路数据，用于上位机的调试。-Serial oscilloscope the XS128 testing procedures, to display the four-way data for the debugging of the host computer.
LSD_TMS320F28027
- tms320f28027 应用例程、常用外设文档资料、源码、串口示波器等-tms320f28027 application routines, common peripherals documentation, source code, and serial oscilloscope
Freescale-real-time-display-speed
- 飞思卡尔单片机和旋转编码器组合测电动机转速程序，通过串口示波器实时上传至PC，同步显示转速-Freescale microcontroller and rotary encoder measuring motor speed, real-time uploaded to PC by serial port oscilloscope, synchronous display speed
chuankoutuxiang
- xc128串口示波器（包含源程序、windows程序等），可移植-xc128 serial oscilloscope (including source code, windows procedures, etc.), portable
virtual-scope
- 飞思卡尔光电组的调试软件，一个虚拟的串口示波器-debug software for fskr，a virtual scope
Arduino-MPU6050-master
- 基于arduino的6050库，可以使用arduino自带串口示波器查看波形(6050 libraries based on Arduino)
PUB
- 使用xlilnx的vivado为基础环境开发的示波器，采用串口屏显示图像(Using xlilnx vivado based environment development oscilloscope, using serial display images)
AOK虚拟示波器上位机源码及APP最新版
- AOK虚拟示波器的上位机源码，从串口获取下位机数据，然后绘制波形(AOK virtual oscilloscope host computer source, from the serial access to the next machine data, and then draw the waveform)
程序
- STC12C5A60S2来完成AD采样，量化编码，同时另一路使用滞后比较器计算频率，将被采样信号存储到一个定义的BUFF内，并上传到串口屏，来显示被测波形(STC12C5A60S2 completes the AD sampling and quantization coding, while the other uses the lag comparator to calculate the frequency. The sampled signal is stored in a define