搜索资源列表
用VHDL语言在CPLD上实现串行通信
- 用VHDL语言在CPLD上实现串行通信-using VHDL on the CPLD Serial Communication
异步串行口
- 一种基于VHDL语言的实现计算机串行通信的简洁设计
VHDL语言的UART串行接口芯片程序
- VHDL语言的UART串行接口芯片程序
crc32校验串行算法
- crc32串行算法,vhdl语言
hh.rar
- 串行输入并行输出 用vhdl语言描述的 有源代码主打色,Serial input parallel output using vhdl language to describe the main color of the source code
用VHDL语言将并行的8位数据换成串行输出
- 用VHDL语言将并行的8位数据换成串行输出-The parallel 8 is the data replaced with the serial output
ADcontroller
- FPGA控制AD7610采样.此为通用控制器模块.其中ADC16BITs串行传入FPGA后,串行数据转换成16BIT并行数据-ADC controller
VHDL-SPI-Module.doc
- 本spi参数化通讯模块是一个支持SPI串行通信协议从协议的SPI从接口。可通过改变参数设置传输的位数,由外部控制器给定脉冲控制传输。-The parameters of spi communication module is a support SPI serial communication protocol from the agreement from the SPI interface. By changing the parameter settings can be transmit
miniUART
- 自适应波特率的通用异步串行接口电路(UART)的VHDL源码,在ALTERA上运行成功-Adaptive baud rate of the universal asynchronous serial interface circuit (UART) the VHDL source code, to run successfully in ALTERA
chuanbingvhdl
- 由于计算机中大部分器件使用的是串行,本程序实现了数字电路中常用的串行输入并行输出的功能。-Because most of the computer using a serial device, the program realization of digital circuits used in serial input parallel output function.
CPLD
- 项目的研究内容是对硅微谐振式加速度计的数据采集电路开展研究工作。硅微谐振式加速度计敏感结构输出的是两路差分的频率信号,因此硅微谐振式加速度计数据采集电路完成的主要任务是测出两路频率信号的差值。测量要求是:实现10ms内对中心谐振频率为20kHz、标度因数为100Hz/g、量程为±50g、分辨率为1mg的硅微谐振式加速度计输出的频率信号的测量,等效测量误差为±1mg。电路的控制核心为单片机,具有串行接口以便将测量结果传送给PC机从而分析、保存测量结果。 按研究内容设计了软硬件。软件采用多周期同
VHDL
- 采用VHDL语言设计一个4通道的数据采集控制模块。系统的功能描述如下: 1.系统主时钟为100 MHz。 2.数据为16位-数据线上连续2次00FF后数据传输开始。 3.系统内部总线宽度为8位。 4.共有4个通道(ch1、ch2、ch3、ch4),每个通道配备100 Bytes的RAM,当存满数据后停止数据采集并且相应通道的状态位产生报警信号。 5.数据分为8位串行输出,输出时钟由外部数据读取电路给出。 6.具备显示模块驱动功能。由SEL信号设置显示的通道,DISPLAY
top
- RS232串行通信,采用VHDL编程,由波特率发生器,接收器和发送器构成-RS232 serial communication using VHDL programming, by the baud rate generator, receiver and transmitter constitute
uart
- 基于FPGA的uart源代码,异步串行通信,vhdl书写的。-uart codes。write with vhdl.
web
- 模拟网络串行通信 近期对计算机间通信比较感兴趣,同时研究usb通信原理,起步为串行通信于是想为更好地理解其机理做一定基础性研究,故做了异步串行通信设计实验。 经过QUARTUS验证,获得了一等奖!-Simulation of the recent serial communication network between the communication of more interested in computers, communications usb at the same time
CRC_16
- crc16的串行和并行写法,而且有详细的测试文件-Serial and parallel crc16 written, and detailed test documents
FPGA_Based_Multi-channels_Serial_ADC_controller.ra
- 采用FPGA控制ADS7844进行模数转换。ADS7844 是Burr_Brown公司推出的一种高性能、宽电压、低功耗的12 b串行数模转换器。它有8个模拟输入端,可用软件编程为8通道单端输入A/D转换器或4通道差分输入A/D转换器,其转换率高达200 kHz,而线性误差和差分误差最大仅为±1 LSB。-Using FPGA control ADS7844 analog to digital conversion. ADS7844 is a Burr_Brown the company intr
adder16b
- 16位串行进位加法器 和值都依赖于上一位的进位信号,即进位信号是串行的经过加法器的每一位。所以进位链的长度与整个加法器的位数有关。-March 16 of the old adding
uart16
- 一个16位的uart,可以实现串行通信,接受或者发送数据!-A 16-bit uart, serial communication can be achieved, accept or send data!
PIANo
- (1)下载“KX232_PIANO_C5T”文件夹中的sof文件。 (2) 接上串行通信线,与PC机通信。 (3)在“FOR_PC_FILE”文件夹中,双击打开上位机软件“SEND”,按键盘上的“1、2、3.。。”即可弹琴。SEND窗口即显示对应的ASIC码。-(1) Download " KX232_PIANO_C5T" folder in the sof file. (2) connected to the serial communication lines, a