搜索资源列表
lowpowertest
- LPC2366低功耗测试代码,通过外部中断唤醒
pmutest
- 基于cortex-m0的低功耗系列芯片LPC1100的功耗程序。该程序采用定时器自唤醒,可以实际应用于很多低功耗项目中。-It s a low power solution program for LPC1100 seria mcu.It can be used for many atcul program for its awake with timer itself.
RF4432.rar
- (1)完整的FSK 收发器 (2)工作于433MHz免费 ISM频段(430.24-439.75MHz),也可以 工作于900.72-929.27MHz的频段 (3)最大发射功率17dBm (4)接收灵敏度高达-115 dBm (5)传输速率最大128Kbps (6)FSK频偏可编程(15~240KHz) (7)接收带宽可编程(67~400KHz) (8)SPI 兼容的控制接口,低功耗任务周期模式,自带唤醒定 时器 (9)低的接收电流(18.5mA),最大发射
Ultra-low_power_electronic_thermometer
- 超低功耗电子温度计-具备功能: (1) 检测温度范围10~30℃,分辨率1℃; (2) 正确显示温度; (3) 整机静态功耗小于5微安(关闭LCD显示,时钟正常运行); (4) 按键唤醒显示; 1.1.2发挥要求 (1) 温度控制功能(能够演示出控制功能的存在); (2) 显示时分秒的时钟功能(能够正常切换和显示); (3) 其他功能;-Have the function: (1) detection of the temperature range 10
999999
- 与MCS-51单片机产品兼容、8K字节在系统可编程Flash存储器、 1000次擦写周期、 全静态操作:0Hz~33Hz、三级加密程序存储器 、32个可编程I/O口线、三个16位定时器/计数器八个中断源 、全双工UART串行通道、 低功耗空闲和掉电模式、掉电后中断可唤醒、看门狗定时器、双数据指针、掉000000~999999计数-he use of analog circuits and digital circuit design of the meter as a whole circuit
Blackfin_hibernate
- 利用Blackfin处理器休眠状态(hibernate休眠模式)实现待机低功耗!!该方法的优点在于能让程序在休眠点被唤醒之后重新运行程序。-Blackfin processor using sleep (hibernate sleep mode) to achieve low standby power consumption! ! The advantages of this method allows the program again after wake-sleep point is r
msp430adc12uart0
- 利用串口调试软件 向串口发送一个字符,MSP430单片机接收到后从低功耗中唤醒,执行AD采样.并将采样结果发送到电脑上的串口调试软件中.单片机发送完后又进入低功耗状态.-msp430f149 usart0 adc12
dsPIC30F_ADC_conversions_in_SLEEP_mode
- dsPIC30F实现的AD转换程序,具有自动唤醒功能,适用于低功耗系统-dsPIC30F AD conversion process implemented with automatic wake-up function, for low-power system
1ms-timer-timing-B
- MSP430F149的定时器B产生大约1ms的定时,使主程序退出低功耗模式。主程序执行一遍流程,再次进入休眠,等待下一次被唤醒。中断TIME_FA次后,改变定时器的定时时间。每次中断的时候翻转P4.1脚的电平,使LED熄灭或者点亮。-MSP430F149 generate approximately 1ms timer timing B, the main program to exit low-power mode. Main program execution once the proces
timer
- 用于MSP430F149。 定时器B产生大约1ms的定时,使主程序退出低功耗模式。主程序执行一遍流程,再 次进入休眠,等待下一次被唤醒。-Timer B to generate approximately 1ms of the time, so the main program to exit low-power mode. Again the main program execution flow, and then Time to sleep, waiti
NRF24LE1-send
- NRF24LE1发送程序,程序每2s向固定地址发送一次数据,发完进入低功耗状态等待唤醒。比官方SDK易懂。-NRF24LE1 to send a program, procedures 2s to a fixed address to send data once, finished to a low power state to wait for the wake....
中断唤醒睡眠系统
- CC2530低功耗中断唤醒程序,定时休眠然后唤醒(CC2530 low power interrupt wakeup program, timed sleep, and wake up)
Cy-STM8
- stm8l系列单片机低功耗使用例程,mcu进入休眠,可通过rtc进行唤醒,从而使功耗降到更低(The stm8l series of single-chip microcomputer's low-power use routine, MCU enters dormancy, can be awakened by RTC, which can reduce the power consumption to lower)
nRF51822
- 这是一个nrf51822无线低功耗配置的例子,。可以内部定时唤醒或者RTC时钟唤醒。(Nrf51822 wireless low power configuration)
睡眠唤醒
- 睡眠唤醒程序,低功耗模式的一种,具有节能的作用。(Sleep wake program, one of low power mode, has the function of energy saving.)
10 低功耗+RTC+IWDG+中断唤醒
- STM8 低功耗模式+rtc+中断唤醒(STM8 low power mode +rtc+ interrupt wakeup)
STM32低功耗工作原理实验程序
- 本源码为基于STM32低功耗原理实验程序,主要实现根据最低电源消耗、最快速启动时间和可用的唤醒源等条件,选定一个最佳的低功耗模式(The source code is an external interrupt program based on STM32, and the point to focus on is the corresponding port clock configuration, pin initialization configuration, and interrupt
stm32l151低功耗及唤醒例程
- 这是stm32f151停止模式的低功耗例程,唤醒方式为RTC定时唤醒。(stm32f151 stop mode example!)
ALIENTEK MINISTM32 实验14 待机唤醒实验
- 在stm32的低功耗模式中,待机模式可以实现系统的最低功耗,在这种模式下,只需要2uA左右的电流。(In the low power mode of STM32, standby mode can achieve the lowest power consumption of the system. In this mode, only 2uA current is needed.)
PWR_RTC低功耗模式代码
- stm32l151低功耗代码,三种模式的低功耗程序,如何rtc alarm唤醒等(Stm32l151 low power code, three modes of low-power program, how to wake up RTC alarm, etc.)