搜索资源列表
利用STM32的TIM定时器产生方波信号
- 利用STM32的TIM定时器产生四个不同占空比的方波信号 。,his example shows how to configure the TIM1 peripheral to generate 7 PWM signals with 4 different duty cycles.
STM32_inPWM.STM32定时器的基本应用
- STM32定时器的基本应用，PWM的输入捕获，硬件调试通过，基本没有误差。,STM32 Timer basic applications, PWM input capture, hardware debugging through, basically no error.
pwm
- STM32的PWM输出模式，STM32的TIM1模块是增强型的定时器模块，天生就是为电机控制而生，可以产生3组6路PWM，同时每组2路PWM为互补，并可以带有死区，可以用来驱动H桥。-STM32' s PWM output mode, STM32' s TIM1 module is enhanced timer module, is inherently for the motor control, it can produce three groups 6-channel PWM,
PWM-51timer
- 用定时器实现的PWM程序,可设置占空比.-Using the PWM timer realize these procedures is to set the duty cycle.
PWM
- 单片机控制按键输出PWM波形 C语言 用两个定时器控制-Single-chip PWM output waveform control button c language with two timer control
STM32-TIM1-PWM
- 通过对 TIM1 定时器进行控制，使之各通道输出插入死区的互补PWM 输出， 各通道输出频率均为17.57KHz。 其中，通道1 输出的占空比为50 ，通道2 输出的占空比为25 ，通道3 输 出的占空比为12.5 。各通道互补输出为反相输出。 TIM1 定时器的通道1 到3 的输出分别对应PA.08、PA.09、PA.10 引脚，而通 道1 到3 的互补输出分别对应PB.13、PB.14 和PB.15 引脚，将这些引脚分别接 入示波器正接线，GND 引脚接示波器负接线，
高级定时器输出1路互补 PWM实验---含详细注释
- 基于STM32单片机设计的高级定时器TIM1的6路互补带死区的PWM输出实验，代码中含有详细的注释，对学习PWM很有帮助(STM32 microcontroller based design of advanced timer, TIM1 6 complementary band, dead zone PWM output experiment, the code contains detailed notes, helpful for learning PWM)
通用定时器PWM输出实验---含详细注释
- STM32单片机通用定时器PWM输出实验---含详细注释，对学习STM32定时器PWM输出有帮助(STM32 microcontroller based design of advanced timer, TIM1 6 complementary band, dead zone PWM output experiment, the code contains detailed notes, helpful for learning PWM)
STM32F103RB高级定时器TIM1控制输出PWM
- 使用ARM芯片STM32F103FRB，利用高级定时器TIM1 PWM模式输出PWM波，控制无刷直流电机，占空比可调。(The use of ARM chip STM32F103FRB, the use of advanced TIM1 timer PWM mode PWM wave output control, brushless DC motor, adjustable duty cycle.)
LQ_eTPU-PWM测试通过
- mpc5634m的ETPU定时器编程官方代码，经过测试(the code of mpc5634 of ETPU)
实验9 PWM输出实验
- 说明：STM32定时器PWM调试例程,希望对你有所帮助((an example of STM32 timer ))
STM19定时器输出4路PWM波可调占空比
- STM32定时器输出四路可调PWM波，经测试可以实现。(STM32 timer output four adjustable PWM wave, the test can be achieved.)
2-TIM—通用定时器-4路PWM输出
- 应用于STM32F103VET6，通用定时器产生4路PWM输出。(Applied to STM32F103VET6, the general timer generates 4 PWM outputs.)
2-7-1、PWM定时器
- 使用STM32内部普通定时器，通过其引脚输出PWM方波，改变占空比查看输出效果(Use STM32 internal regular timer, output PWM square wave through its pin, change duty ratio to view output effect)
通用定时器(Timer)
- 此为ARM1138开发板的几个关于通用定时器的范例程序，包括32位/16位单次触发定时，32位/16位周期定时/RTC定时，PWM应用等。(This is a few examples of general timer for ARM1138 development board, including 32 bit /16 bit single trigger timing, 32 bit /16 bit cycle timing /RTC timing, PWM application and
PWM输出实验
- 利用STM32F407的内部定时器，产生一路PWM波(Using the internal timer of STM32F407 to produce a PWM wave)
17.使用TIM1定时器产生PWM波形输出
- 单片机STM8使用TIM1定时器产生PWM波形输出(Single chip microcomputer STM8 uses a TIM1 timer to produce PWM waveform output)
定时器主从方式输出可控个数的PWM脉冲
- 一个关于STM32定时器主从方式输出PWM脉冲的程序(A program about STM32 timer's master slave mode to output PWM pulse.)
TIM-高级控制定时器PWM输出
- stm32F103 TIM1输出7路PWM STM32F103ZET6总共有8个定时器，TIM1和TIM8是高级控制定时器，TIM2、3、4、5是通用定时器， TIM6和TIM7是基本定时器。 本例程实现高级控制定时器TIM1总共7个功能引脚输出PWM波形。(STM32F103ZET6 has 8 timers in total, TIM1 and TIM8 are advanced control timers. This routine implements an advance
12. PWM呼吸灯实验
- 基于stm32f407对定时器PWM功能进行配置并使用(Configuration and use of timer PWM function based on stm32f407)