搜索资源列表
自动完成寄存器配置的44b0定时中断和ADC程序
- 自动完成寄存器配置的44b0定时中断和ADC程序-automatically register configuration of the suspension and 44b0 regular procedures ADC
8251定时器，复位功能汇编
- C32中C语言中嵌入汇编程序示例.包括中断程序中调用C参数-C32 C language embedded assembler example. Including the interruption procedure called C parameters
用8253-8255编写的定时响铃程序
- 用8253-8255编写的定时响铃程序 可以定时两个时间点，很经典的程序-spent 8253-8255 prepared by the regular beep procedures regular two points in time, classic procedures
timer2interrupt
- 飞思卡尔的中断和定时程序给初学者看的 学习交流-Freescale procedures and timing of the interruption to the beginners learn to read
ARM_LPC_timer
- LPC21xx ARM7 定时程序 定时控制LED-LPC21xx ARM7 regular procedures for timing control LED
LM3S811-time
- ARM LM3S811 定时时钟显示程序，-ARM LM3S811 time display program
用c实现按键的状态分析法的程序
- 本程序就是非常有用的状态分析法实现按键程序，用c语言编写，在51内核的单片机中成功实现，对于嵌入式开发者非常有用，该程序只用了4个按键，实现了时钟显示、调整、定时、遥控、闹钟等许多功能，适合于有一定基础的开发者用。
AVR单片机定时器
- 采用ATmega16的单片机定时器程序，使用中断方式(this is a Timer designed with Atmega16)
用定时器控制指示灯
- 此程序是nrf52832系统的小程序，作用是用LED显示定时器运行状态。(This program is a small program nrf52832 system, the role is to use LED to display the timer running state.)
定时器
- 用STM32F103C8T6芯片完成定时器功能。主要是一些配置可以参考，还有注意中断服务程序。(Use STM32 chip to complete timer function)
实验18：定时器1中断
- 51开发板中第10个定时器中断，运行程序后会自动运行相关程序(The 10 timer interrupts on the development board, and the program will run automatically after running the program)
ALIENTEK MINISTM32 实验7 定时器中断实验
- 基于STM32F103RCT6mini开发板定时器中断上更改的HC-SR04超声波程序，亲测可用(The HC-SR04 ultrasonic program based on the STM32F103RCT6mini development board timer interrupts changes, and the pro test is available)
STM8S105定时器2精确延时
- STM8S105的定时器2的精确延时程序(STM8S105 timer 2 precise delay program)
通用定时器(Timer)
- 此为ARM1138开发板的几个关于通用定时器的范例程序，包括32位/16位单次触发定时，32位/16位周期定时/RTC定时，PWM应用等。(This is a few examples of general timer for ARM1138 development board, including 32 bit /16 bit single trigger timing, 32 bit /16 bit cycle timing /RTC timing, PWM application and
STM32定时器中断程序
- 本源代码为讲解基于STM32的定时器中断程序，通过定时器TIM3产生间隔1秒钟一次的中断，在中断中控制LED发光二极管，每次中断都使发光二极管状态取反(This source code is explained based on the STM32 timer interrupt program, through the timer TIM3 interrupt an interval of 1 second, in the interrupt control LED light-emittin
步进电机参考程序 带注释
- 适合改多轴步进电机控制。使用定时器中断与外部中断实现。使用步进电机驱动器。(Suitable for multi-axis stepper motor control. Using timer interrupts and external interrupts. Use a stepper motor driver.)
舵机程序
- 利用PWM，改变定时器的占空比来控制舵机(Using PWM to control the rudder)
定时器主从方式输出可控个数的PWM脉冲
- 一个关于STM32定时器主从方式输出PWM脉冲的程序(A program about STM32 timer's master slave mode to output PWM pulse.)
PMC232定时中断和PWM输出
- 应广单片机PMC232的ADC 和PWM的代码程序，使用PAD-AUK-0.82开发环境(We should use the ADC and PWM code program of PMC232 and use PAD-AUK-0.82 to develop the environment.)
智能型可通信塑壳断路器程序源代码
- 根据产品的设计功能，软件主要由以下几部分组成：主流程、定时器中断、输入输出信号设别、执行电磁脱扣器驱动等。(According to the design function of the product, the software mainly consists of the following parts: mainstream process, timer interruption, input and output signal setting, electromagnetic relea