搜索资源列表
led
- 该程序为led跑马灯程序，实现gm8180开发板上4个led循环点亮。-The program is led Marquee procedures to achieve gm8180 development board 4 led light cycle.
t1
- led灯，实现循环点亮led灯，实现霓虹灯的状态显示-led lights, led lights light to achieve circulating, to achieve the state of neon display
led
- led数码管动态扫描控制，循环点亮，可在keil环境下编译-Dynamic scan control led digital tube, cycle light, in keil compiler environment
LED
- 循环点亮P1口对应的8个LED灯，造成循环流水点亮的效果-Cycle corresponds to the P1 port is lit 8 LED lights, the effect of light caused by recirculating
led
- 动态的霓虹灯 在同一时间内8个LED循环点亮并闪烁，使用一个8×8点阵LED显示“生命在于运动”，-led
led
- 本实验完成发光二极管的循环点亮实验，由于输入晶振为20M，分频得到count1信号，故每间隔约1S彩灯循环移位一次。 也可以外接32768hz的晶振经4060分频后的1HZclk输入，自己可以尝试改变实验，加以练习。-In this experiment completed the cycle of light-emitting diode light experiments, as a result of the importation of crystal for the 20M, sub-
led
- 学习PIC16F87xA的初级程序,LED点亮+4LED循环点亮-Base learn for PIC16F87xA,Light LED and 4 LED around light
led-deng
- 51单片机循环点亮8个led小灯，使其不断变化的闪烁-51MCU cycle lights 8 led a small lamp
led
- 用VHDL编程点亮发光二极管，并实现二极管循环点亮的功能 -Light emitting diode, light diode loop using VHDL programming
liushuideng
- 流水灯实验，实现开始灯全亮，然后依次点亮，此后循环点亮led灯。-Light water experiments, the realization began to full bright light, followed by light, then cycle light led lights.
led
- 这是一个基于FPGA的数码管点亮程序，从0到F循环点亮。-This is a based on FPGA digital tube light program, from 0 to F light cycle.
led-roll
- AT8951单片机的proteus仿真 实现LED循环点亮 是学习单片机和proteus的入门资料-AT8951 microcontroller simulation proteus LED cycle lights up learning microcontroller and proteus introductory information
STM32-LED
- STM32 跑马灯例程 可以实现两个LED灯的循环点亮-STM32 LED
8LED
- 开关控制循环点亮LED 三种方式:跑马灯 流水灯 弥红灯-Switch control cycle light LED three ways: Marquee indemnity red light water
LED1_C
- 单片机循环点亮LED，适用于凌阳61单片机。-SCM cycle light LED
Cycle-the-lights
- msp430g2553单片机 循环点亮led灯-msp430g2553 MCU cycle light led lights
LED
- 驱动LED使其形成跑马灯，循环点亮，设计dave配置和keil-Drive LED to form a Marquee
led
- stc51系列单片机控制led左循环点亮-stc51 Series MCU control led Left light cycle
LED
- 51单片机汇编编程 可实现led等的点亮，循环点亮等。-51 microcontroller programming can achieve such light led, light cycle and so on.
LED
- 嵌入式arm裸板LED程序，使灯循环点亮-Embedded arm bare board LED program