搜索资源列表
liu-shui-deng
- 流水灯程序，循环点亮P1口对应的8个LED灯，造成循环流水点亮的效果-Water chase, cycle light P1 port corresponding to the 8 LED lights, resulting in the light of the effect of recirculating
s5_led
- 本实验是利用底板上的 LED 灯，实现LED 灯的循环点亮。-This experiment is the use of LED lights on the bottom plate, the cycle of the LED lamp is lit.
exp3
- 花样流水灯：8个发光二极管D1~D8分别接在单片机P0.0-P0.7端口上，一个开关接在P3.0上。要求输出端口输出“0”时，发光二极管亮。开关闭合时，开始按P0.0+P0.7、P0.1+P0.6、P0.2+P0.5、P0.3+P0.4的顺序依次点亮LED，再按P0.3+P0.4、P0.2+P0.5、P0.1+P0.6、P0.0+P0.7的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-Mood Light water: 8 LEDs D1 ~ D8, respectively, c
liushuideng
- 多种方式点亮LED灯，依次循环，可控制改变方式-A variety of ways to turn on the LED lights, turn cycle control to change the way
scanled
- 利用FPGA系统电路控制8个LED进行4种工作模式状态的循环显示,这四种工作模式状态是：（1）从左到右逐个点亮LED（2）从右到左逐个点亮LED（3）从两边到中间逐个显示LED（4）从中间到两边逐个显示LED.-The FPGA system circuit control 8 LED status of the four operating modes cycle through four operating modes state: (1) from left to right by-lit
main6
- stm32 裸机跑马灯程序可以控制四盏LED循环点亮-stm32
K1-K4-packet-control-LED
- 每次按下 K1 时递增点亮一只LED，全亮时再次按下则再次循环开始， K2按下后点亮上面4 只LED，K3 按下后点亮下面4 只LED，K4 按下后关闭所有LED-Each press K1 increments lit a LED full brightness when pressed again, the cycle begins again after 4 LED lit above press K2, K3 Press lit following four LED K4 Press
PIT_a_EXTI
- K60的定时中断和外部中断，可以实现进入定时中断循环点亮2个LED灯，同时嵌入外部中断，控制LED亮灭-K60 the timer interrupt and external interrupt, lit two LED lights into the timer interrupt cycle, while embedding external interrupt control the LED light off
K1-K4-packet-control-LED
- 每次按下 K1 时递增点亮一只 LED，全亮时再次按下则再次循环开始， K2 按下后点亮上面 4 只 LED，K3 按下后点亮下面 4 只 LED，K4 按下后关闭所有 LED -Each press K1 increments lit a LED full brightness when pressed again, the cycle begins again after 4 LED lit above press K2, K3 Press lit following four LE
Numb-LED
- 基于51单片机的LED数码管动态显示，LED数码管动态显示就是一位一位地轮流点亮各位数码管，对于每一位LED数码管来说，每隔一段时间点亮一次，利用人眼的“视觉暂留"效应，采用循环扫描的方式，分时轮流选通各数码管的公共端，使数码管轮流导通显示。-Based on 51 single-chip LED digital tube dynamic display, LED digital tube dynamic display is a bit lit Members take turns digit
114455
- 用P1口控制8个LED，按P3口输入信号的不同模式选择4种16次循环点亮方式，用软件延时实现1秒的扫描周期。将生成的HEX文件下载到实验板上验证-8 LED control port with P1 and P3 port input signal different modes to choose four kinds of 16 cycles lit way second scan cycle software delay. Will generate the HEX file is dow
longxin_diandeng
- 试验在龙芯板子上的led灯循环点亮，已经验证可以用，开发环境linux2.6-realize the led on and off on longgon
jiaotongdengTimer.rar
- 51单片机IO口控制以及定时器的使用方法，控制LED灯循环点亮，或者模拟路口交通灯的变化。,51 MCU IO port control, and the use of the timer, control LED lights cycle lit or analog junction traffic lights change.
shuzuxunhun
- 单片机开发，控制led灯，按照数组循环方式点亮led灯-Microcontroller development, control array circulation lit led lights
led
- arm9的LEd灯点亮程序，4个LED全亮1秒后全灭，再过1秒全亮，如此循环-arm9 the the LEd lights lit program, four LED full brightness for one second all off, one second later full brightness, so the cycle
dspic30f6014_led
- dspic 循环点亮6个贴片LED灯，单片机芯片采用Mcrochip dspic30f6014.-Dspic circular light 6 strips of LED lamps, microcontroller chips use Mcrochip dspic30f6014.
led3
- 可以实现LED流水灯循环点亮的小程序,简单明了-LED light water cycle light program, plain and simple
GPIO_Test
- TI公司生产的低功耗BLE蓝牙芯片的基础实验利用GPIO口驱动底板上的LED灯，使四个led循环点亮和熄灭-TI' s low-power production of basic experimental BLE Bluetooth chip GPIO port driver using the LED lights on the bottom, so that the four led cycling on and off
Light-water
- 本程序为单片机简单应用程序，实现的是8只led灯循环点亮的功能。-This simple procedure for microcontroller applications, the realization of the 8 led lights light cycle function.
EX01_GPIO_LED
- DSP经典入门例程，GPIO流水灯实验，F2812芯片，循环点亮GPIOA的灯，时间间隔为300ms。-DSP F2812 source code ，GPIO led experiment.