搜索资源列表
digital-clock
- 数字时钟程序,实现年月日时分秒的计时,用于Altera 内置处理器-digital clock
ClockQUARTUSVHDL
- 12/24小时数字时钟VHDL设计 包括顶层文件的设计和VHDL源程序-12/24 hour digital clock design, including the top-level VHDL design and VHDL source code file
shizhong
- 数字时钟的设计带有有秒表,闹钟功能,Keil源程序-The design of the digital clock with a stopwatch, alarm clock function, Keil source program
clock--jiaoshi
- 基于verilog简单数字时钟程序,可实现校时,校分功能-Based verilog simple digital clock procedures, can be achieved when the school, school division function
Digital-clock
- 基于FPGA实现数码管数字时钟功能 使用芯片为EP2C8Q208C8N,使用数码管显示数字时钟,使用Verilog语言编程,本例子有工程文件、仿真、波形,经过测试可以使用。-Based on FPGA digital tube digital clock function uses chip EP2C8Q208C8N, use digital display digital clock, using Verilog language programming, the present exam
menu128x64
- 多级菜单,电子数字时钟系统,日期,时间,温度显示-Multi level menu, electronic digital clock system, date, time, temperature display
LCD1602-shows-the-clock
- LCD1602显示时钟,控制单片机连接的LCD1602显示数字时钟,很实用。-LCD1602 shows the clock,Control microcontroller LCD1602 connected to the digital clock, very practical。
shizhongjiemian
- 这是一个嵌入式中基于minigui编程实现的数字时钟程序,可获取当前系统时间,并可调节。-This is an embedded minigui programming based on the realization of the digital clock procedures, access to the current system time, and can be adjusted.
test5
- 本实验要求完成的任务是在时钟信号的作用下,通过输入的键值在数码管上 显示相应的键值。在实验中时,数字时钟选择 1KHZ 作为扫描时钟,用四个拨动 开关做为输入,当四个拨动开关置为一个二进制数时,在数码管上显示其十六进 制的值。 实验箱中的拨动开关与 FPGA 的接口电路,以及拨动开关 FPGA 的管脚连 接在实验一中都做了详细说明,这里不在赘述。-The experiment required to complete the task in the role of the clo
clock
- 数字时钟设计 设计一个数字时钟 要求:(1)用数码管显示时/分/秒 (2)有时间预置功能 (3)能用蜂鸣器报时-Digital Clock Design Design a digital clock Requirements: (1) with the digital display hours/minutes/seconds (2) has the time preset function
digit_clock
- 四位数码管数字时钟,两个按键,按键长按设置,短按调时间。-Four digital tube digital clock, two buttons, press the key to press the set, short press the time.
digital-clock-circuit-.ms13
- 数电_Multisim设计_数字时钟电路 (显示时:分:秒 CP 频率 f 1Hz) 【电路说明】 1 基于 74LS160 做三个计数器(时:24 进制,分:60 进制,秒:60 进制) 2 秒针计数器完成一次计数后,进位给分针计数器的 P 和 T。 分针计数器完成一次计数后,进位给时针计数器的 P 和 T。-Digital circuit _Multisim design _ digital clock circuit (Display: hours: minutes
smart clock by C52
- 使用STC89C52和SHT20芯片实现以下功能:数字时钟,按键一切换状态(显示时间状态、调整时间状态、显示温湿度状态),按键二实现在调整时间状态下对时间数字加一的功能。
Electric_clock
- Verilog数字时钟,已实现Diamond环境仿真与FPGA硬件测试-Verilog digital clock, has achieved Diamond FPGA hardware simulation and test environment
dingshizhongv
- 通过电子 定时器定时 到1s给一个中断 让单片机去执行中断 跳转至相应的数码管位 然后修改当前显示值 再设置到10进位加一 之后就出来数字时钟的效果-Through the electronic timer 1s to a microcontroller to the interrupt interrupt to jump to the corresponding bit digital tube and then modify the current display value is se
Digital-clock
- 4位显示数字时钟,带闹铃,PDF8563,包含驱动文件,可直接使用或移植-4 bit display digital clock, with alarm, PDF8563, including driver files, can be used directly or transplantation
0037、基于单片机的数字钟设计论文资料
- 本设计以单片机AT89S52为切入点,通过使用AT89S52的内部的可编程定时器/计数器,结合对外接晶振的调节来确定一个合适的振荡周期,从而确定出内部的机器周期。再通过对内部中断程序的设置来设计出时钟程序,即设计出了电子时钟的核心。然后在核心电路的基础上设计出了相应的扩展电路,使本设计更加实用。(The AT89S52 single-chip design as the starting point, through the use of AT89S52 internal programmabl
51中断定时数码管显示程序
- 采用51单片机通过中断来进行精确定时,然后通过数码管显示,来完成一个精确数字时钟的功能()
至简设计法--闹钟
- 闹钟 工程说明 本工程包括矩阵键盘和数码管显示模块,共同实现一个带有闹钟功能、可设置时间的数字时钟。 案例补充说明 我们通过建立四个清晰直观的模块(数码管显示模块,矩阵键盘扫描模块,时钟计数模块,闹钟设定模块),以及建立完善的信号列表和运用verilog语言编写简洁流畅的代码,实现电子闹钟时、分、秒计时以及设置、修改、重置等功能。(alarm clock Engineering descr iption This project includes matrix keyboard and di
clock
- 数字时钟的实现,数码管显示,实现时分秒的显示(The realization of the digital clock)