搜索资源列表
shumaguandongtaixianshichengxu
- 基于51单片机的数码管动态显示程序,是常见的数码管显示程序-51 single-chip microcomputer-based digital control of dynamic display program, is a common digital tube display program
PIC_calc_seg_key16
- 采用模块化格式编写的基于PIC单片机的简单计算器,采用4*4键盘输入,4位数码管输出,电路图为kb16seg74ok.DSN。 MPLAB V7.1+HI-TECH V8.05+Proteus V7.1-Modular format PIC MCU-based simple calculator, the use of 4* 4 keyboard input, 4 digital tube output circuit for kb16seg74ok.DSN. MPLAB V7.1+ HI-TE
chenggong
- 实现由一个4位十进制数码管(含小数点)显示结果,其测量范围为1Hz~9999KHz,能自动根据7位十进制的结果,自动选择有效数据的高4位进行动态显示(即量程自动转换),小数点表示是千位,即KHz,-To achieve a 4 decimal digits (including decimal point) shows the results of its measurement range of 1Hz ~ 9999KHz, automatically in accordance with t
8LU
- 八路抢答器,具有时间设置,报警功能,使用四位共阳数码管-Answer eight-way, and time settings, alarm function, the use of a total of four digital tube Yang
001
- 【004】流水灯实验 [51].doc 【006】多位数码管动态显示 [51].doc 【041】四位数码管计数演示.doc -【004】 light water experiments [51]. Doc 【006】 many dynamic display of digital control [51]. Doc 【041】 four digital tube count demonstration. Doc
Quartus4
- 1实现六个数码管串行扫描电路 2六个数码管滚动显示电路-1 to achieve the six digital control circuit 2, six serial digital scanning tube rolling display circuit
DE2_LCM_CCD
- DE2 CCD数码相机源代码,下载即可使用。方便学习。-DE2 CCD digital camera source code, you can use to download. Facilitate learning.
18b20
- ds18b20温度控制程序,数码管显示、三键控制-ds18b20 temperature control procedures, digital display, three-button control
DS18B20
- 基于DS18B20的小型温度测量系统,用的是7端数码管显示,我帮别人做的毕业设计-DS18B20
NIOS_seddisplay
- NIOS七段数码管显示系统设计,包括完整的硬件合软件设计-NIOS Seven-Segment LED Display System Design
DVP3000J
- ET6202驱动数码管显示,每个按键显示一个数字,用AT89S51作MCU-ET6202-driven digital display, each button displays a number for the MCU to use AT89S51
DigitalPhotoFramePannel
- 数码相框屏的控制代码,有原理图,针对性的介绍相应TFT屏的驱动控制-Digital Photo Frame screen control code, a schematic diagram, the corresponding targeted introduction of the drive TFT screen control
CH451DS1
- 数码管驱动及键盘控制芯片CH451,基本应用资料-LED driver and the keyboard control chip CH451, the basic application information
keypad
- 4*4按键扫描经典程序与8位数码管动态显示-4* 4 keypad scanning procedures and classic 8-bit digital tube dynamic display
DS18B20--lcd
- 用单片机STC89C52开发,用温度DS18B20芯片感应温度,并显示到共阴数码管上。 (我用的是keil软件编译,上面没看见啦)-STC89C52 with single-chip development, chip temperature DS18B20 the temperature sensors and displays to the digital control on a total of Yin. (I use software keil compiler, you d
51singlechipclockusingtimers
- 51单片机利用定时器做的时钟,4按键操作,共阳数码管显示。-51 single-chip clock using timers do, 4 button operation, a total of positive digital display.
LEDdemo
- stc89c52控制的数码管显示,带按键设置启始时间-stc89c52 digital control display, with key set start time
AD_count_countdown
- 设置3个功能键:当某一功能键被按下后,进入相应的功能模式。3个功能有: 1)8路数据采集功能:通过调节可变电阻实现0-5V的电压输出作为8路输入信号使用,每路信号用2位LED显示采集的结果。报警:任意一路超过某一门限(可自己设定)时,发出报警(声音+灯闪烁,并通过灯指示是哪一路报警),同时停止采集。2)计数功能:利用计数功能键,实现每按一次按键,LED显示加1,从0-99计数。3)秒表功能:只用一个键控制。按下一个按键后时钟启动,从零开始计时,计时间隔0.01秒,再按一次后停止。再按一次后清
LEDhuihui
- 8*8 led 数码管显示,女朋友做的,很棒哦,动态扫描的方法。-8* 8 led digital tube display, a girlfriend to do, oh great, dynamic scan method.
shuziclock
- 长按 键3s 进入调时状态,此时显示分的2个数码管闪烁,这时可进行加减调时,再按模式键,可看到显示时的2个数码管闪烁,可对时进行加减调整。再按模式键退出调整状态,进入正常工作状态。-Button to enter the transfer length when the 3s state at this time showed that two-point digital control blinking, then addition and subtraction can be transfe