搜索资源列表
ceshi
- 基于BMP180气压芯片的便携式气压海拔温度测量仪的51单片机程序-BMP180 pressure chip based portable pneumatic elevation of temperature measuring instrument of 51 single-chip microcomputer program
ms5611Poled1306ssd-0.96
- 用51作为主机。ms5611气压传感器测量气压及温度并转化为高度,将数据用oled显示。包括软件模拟IIC及硬件SPI通讯方式。-With 51 as the host. Ms5611 barometric pressure sensor to measure air pressure and temperature and into a high degree, the data with oled display. Including software analog IIC and hard
V1.33B-161008056
- 雪利曼ZB299仪表打气程序放电程序,强制工作10公斤气压-ansm,hheuio who,qahusn.djkk derrr hfgtyuivv
HT_Hawk_236
- 开源四轴最新版V2.63,涉及四元素解算角度,气压定高等,值的学习(Open source four axis of the latest version of V2.63, involving four elements calculation angle, barometric rating, higher value learning)
气压检测
- 通过气压计BMP180 得到数据在串口上传(The barometer BMP180 gets the data)
Get Pressure
- STM32F103RCT6,通过IIC驱动BMP280,获得气压、温度、高度等数据,实测得出数据很正常(STM32F103RCT6, through the IIC drive BMP280, access to pressure, temperature, height and other data, measured data is normal)
Bluetooth enviroment monitor
- 集成了温湿度传感器、气压传感器、光敏传感器的采样。(Samples of temperature and humidity sensors, air pressure sensors and photosensitive sensors are integrated.)
微型气象站
- 平台为arduino uno r3,采集温湿度,气压、海拔、土壤湿度信息在5110屏幕上显示,并通过nrf24l01传到另外一个arduino采集板上,然后通过串口传给pc机。传感器有ds18b20,dht11,土壤湿度传感器,bmp085,显示屏为5110,一对nrf24l01。library文件夹下为所需的各种库。(The platform for Arduino uno R3, collecting temperature and humidity, air pressure, altit
bmp180气压检测
- bmp180 厂家资料,有示范程序,亲测可用。(Bmp180 manufacturers information, there is a demonstration program, pro test available.)
STM8L - BMP280
- STM8+BMP280采用SPI方式驱动,测量压强(STM8+BMP280 is driven by SPI to measure pressure)
20140915_方程式换挡
- 用飞思卡尔单片机MC9S12XS128编写的方程式赛车采用气压阀门换挡的程序。(The program is for the MC9S12XS128 microcontroller which used for the shift gear with air pressure valve in Formula car.)
DHT11,BMP180组合
- 采集温湿度气压加显示到显示屏上,采用STM32(Collecting temperature and humidity pressure to display, using STM32)
Stm32F407_Template_iar
- STM32F407的气压传感器MS5611控制程序(STM32F407's air pressure sensor MS5611 control program)
GY-65气压模块发送资料
- 使用BMP085气压计进行测量高度的源代码,包含arduino,51,avr三种(Use BMP085 barometer to measure the height of the source code, including Arduino, 51, AVR three kinds.)
bmp180
- iic总线方式读取数字气压传感器BMP180数据,数据显示到oled(IIC bus reads the digital pressure sensor BMP180 data, and the data is displayed to OLED.)
bmp180
- 气压值 温度值的检测 并通过该值计算当地的海拔高度(Detection of the temperature value of the pressure value)
计控实验胎压监测
- 本系统由胎压监测模块和中央监视模块两部分组成。胎压监测模块安放在轮胎内用于检测轮胎压力后经无线模块传输给位于车内的中央监视模块。胎压监测模块由控制器单片机,气压传感器和,电源模块和无线发射模块组成;中央监视模块由控制器单片机,液晶,声光报警装置,电源模块和无线接收模块组成。系统硬件框图如下。(The system consists of two parts: tire pressure monitoring module and central monitoring module. The ti
bmp180-noh
- esp8266通过I2C总线读取bmp180芯片的气压和温度值,不用库文件的代码。(Esp8266 reads the pressure and temperature values of the bmp180 chip through the I2C bus, without the code of the library file.)
bmp180
- bmp180读取温度气压,通过1602显示(Bmp180 reads the temperature pressure, show with 1602)
STC8K_SHT20_BMP280_DEMO
- KEIL C51开发,自用程序,完美测试通过,STC8A8K64S4 读取SHT20温湿度 BMP280气压数据,I2C协议,STC8A8K64S4 时钟选22.1184M(STC8A8K64S4 read SHT20 temperature and humidity BMP280 air pressure data, I2C protocol)