搜索资源列表
我参加电子竞赛 做的温度控制的单片机程序
- 主要用到了PID算法控制温度,显示采用动态扫描.输出可调节占空比的脉冲控制加热器-mainly used to control the temperature PID algorithm, shows that using dynamic scanning. Output adjustable pulse duty cycle control of the heater
temcotrl
- 温度自动控制,设置温度,低于一个温度加热,高于一个温度风扇工作降温。-Automatic Temperature Control, equipped with a temperature below a heating temperature, a temperature higher than the cooling fan work.
temp_finish
- MSP430开发的使用PID算法温度控制程序 本程序通过485总线与上位机通信发送和接受命令,并自动通过PID算法控制温控板的温度加热到37度或制冷到16度,是我工作后完成的第一个工程项目
temprature.rar
- 该源代码为基于AVR单片机的温度加热控制系统的源程序。测温采用的的是热敏电阻,加热控制采用的是PID算法。另:编译器我用的是CVAVR 版本号是1.25.7a,The source code for AVR-based single-chip temperature heating control system of the source. Temperature measurement is used in thermistor, heating control PID algorithm i
IO_Test_NTC
- 这是一段利用单片机IO口作的温控程序,感温元件是NTC。功能是,当温度低过某值时开始加热, 随着温度上升。。。当高到某值时停止加热,然后开始冷却。。。不断重复。。。,使用时要注意 RC常数,常数过大会造成16位计数溢出,得不到正确结果。程序是作产品前的一个试验程序,当时 调试已通过,能作到±0.5℃。-This is a single-chip IO port for the use of temperature control procedures, temperature se
LCD2402
- 本装置的功能是对温度进行实时监测与控制。由温度传感器DS18B20对温度进行采样和转换成数字信号送入单片机,并与设定的报警温度上、下限值进行比较,信息通过LCD显示出来。如实时温度超过设定的上、下限值,一方面由LCD显示信息,并发出警报声;另一方面自动控制继电器(Relay)开接通或断开,从而控制加热源的开与断,达到对温度进行实时控制的目的。-The device s function is to conduct real-time temperature monitoring and cont
ddd
- 快热式热水器程序。循环调用显示、键扫描、温度检测、加热控制函数。 判断是否加热、加热功率及档位指示灯处理。-Quick-style hot water heater program. Cycle of calls shows that key to scan, temperature detection, heating control function. Determine whether the heating, heating power and light treatment stall
temperaturecontrl
- 温度控制器,采集当前空间温度,当温度大于某个值,就关闭加热器,当温度小于某个值就启动加热器-Temperature controller, collecting the current space temperature, when the temperature is greater than a certain value on the closure of the heater, when the temperature is less than a value on the start
luwenjianceqi
- 试设计一电加热炉控制系统,使其能同时对一般家用电炉的温度进行控制。利用传感器和变送器检测出炉内的温度,根据温度值与设定值的差值以及该差值随时间的变化率实施控制-Try to design a control system for electric heating furnace so that it can simultaneously ordinary household furnace temperature control. The use of sensors and the trans
PID
- 用于自动喷胶机的PID算法,基于热熔胶的加热温度控制,过冲不高过2度,精度有0。5度-For automatic glue machine PID algorithm, based on hot melt adhesive heating temperature control, overshoot does not exceed 2 degrees, the precision of 0.5 degrees
tem
- 实现温度控制,并带有自动报警功能。温度过低时加热,温度过高时降温。-To achieve temperature control, and with an automatic alarm function. When the temperature is too low heating temperature when the temperature is too high.
1111
- 通过键盘设定温度和加热时间。 (2)使用DS18B20采集温度,采用七段数码管显示当前温度和剩余时间,并和设置的温度进行比较。 (3)当温度低于设定值时,通过DAC0832输出电压供给发热电阻RT1,使其温度升高。 -Through the keyboard setting temperature and heating time. (2) The use of DS18B20 collecting temperature, using seven-segment digital t
diankaoxiang.c
- 电烤箱作为一种重要的生产工具广泛的应用于工业生产和食品加工等领域。电烤箱的温度是生产工艺的一项重要指标,对温度的控制性能在很大程度上决定了产品的质量和生产效率。 系统以P89V51RD2单片机为核心,实现了温度采集、PID控制、人机对话以及定时等功能。由于干扰和实际噪声的存在,在采样过程当中会出现采样信号与实际信号存在偏差的现象,为了减小这方面原因造成的测量误差,系统采用了16次采样取平均值的方式对采样值进行平滑滤波,再对滤波值查表就得到了实际的温度值。在控制方面采用PID控制,温度控制具有
abc
- 设计以89c52单片机为核心,采用了温度传感器AD590,A/D采样芯片ADC0804,可控硅MOC3041及PID算法对温度进行控制。该水温控制系统是一个典型的检测、控制型应用系统,它要求系统完成从水温检测、信号处理、输入、运算到输出控制电炉加热功率以实现水温控制的全过程。-89c52 microcontroller as the core design, using a temperature sensor AD590, A/D sampling chip ADC0804, triac MO
DS18b20
- 本设计采用无ROM的8051作为主控制芯片。8051的接口电路有8155,2732和ADC0809等芯片。8155用于键盘/LED显示器接口,2732可作为8031的外部ROM存储器,ADC0809为温度测量电路的输入接口。 本设计温度控制电路是通过可控硅调功器实现的。双向可控硅管和加热丝串联接在交流220V,50HZ交流市电回路,在给定周期内,8031只要改变可控硅管的接通时间便可改变加热丝功率,以达到调节温度的目的。 -This design uses no ROM 8051 as
LCD_18B20_temp-v1.1
- 基于51的液晶、温度传感器进行温度加热的控制-51 LCD, temperature sensor, temperature control of heating
dianjiare
- 电加热锅炉温控程序,可进行温度加热控制。单片机芯片为51系列。-Electric heating boiler thermostat program, the temperature heating control. Microcontroller chip 51 series.
51单片机温度控制原码文本
- 51单片机温度控制程序,可应用于环境温度测试及冰箱和制冷设备的温度监测、控制,可根据代码对端口的定义,接入继电器控制加热设备及制冷设备。(51 single-chip temperature control procedures, temperature monitoring and control can be applied to environmental temperature test and refrigerator and refrigeration equipment, acco
温度报警系统(帮胡欢制作)
- 通过18B20传感器检测水温温度加热到用户设定的值(含PCB原理图和51C代码)(Water temperature is detected by 18B20 sensor and heated to user settings (including PCB schematics and 51C code))
基于stm32f103指南者开发板的温度控制系统
- 使用stm32F103开发板利用PID算法控制PWM信号控制大功率MOS管通断,为一个20Ω/30W的空心瓷管电阻加热。在控制温度过程中通过温度传感器(DS18B20)实时监测系统温度,并使用stm32F103开发板所提供的电阻式触摸屏显示实时温度和预设温度及温度控制面板。(Using the stm32F103 development board, the PID algorithm is used to control the PWM signal to control the high p