搜索资源列表
jiyuGSMfd
- 本系统主要由单片机和GSM短信模块组成，借助最可靠、最成熟的GSM移动网络，以最直观的中文短消息或电话形式，直接把报警地点的情况反映到您的手机屏幕上。它采用主动式红外传感器进行检测，变有形的传统防盗网防盗窗为无形，给火灾时的逃生提供方便。并配备烟雾传感器和燃气泄漏传感器，实现防火、防燃气泄漏的作用。-The System is made up of MCU and GSM Modem. It will display the alarm content in Chinese directly a
MCU_development_example_of_the_classic_design_of_s
- 单片机开发实例之烟雾报警经典设计MCU development example of the classic design of smoke alarm-Single Chip classic example of the smoke alarm design MCU development example of the classic design of smoke alarm
fengmingqiyinyue
- 自己写的蜂鸣器音乐程序，还可以和烟雾报警系统和结合。-Write their own music program buzzer, you can and smoke alarm systems and integration.
Smart-Socket
- 智能插座。可定时通断，手动按钮通断。烟雾模块烟雾报警，人体红外热释电检测到人体信号打开液晶背光灯。液晶为VTK3224智能液晶。含防雷模块，电能计量模块-Smart outlet. Can be time-off, manual on-off button. Smoke smoke alarm module, pyroelectric infrared detecting human body' s signal to open the LCD backlight. LCD is VTK3
FEII
- 烟雾报警器源程序,可以检测到无烟时不退出报警。-Smoke alarm source, can be detected when the smoke alarm does not exit.
master-slaver
- 实现烟雾报警的主从机程序,主机轮巡检测各端子，有烟雾时主机报警-the master-slaver program of being used to realize the smoke detection ,the master takes turns to check the each terminal node ,when checking the smoke ,then alarm
ds18b20PhongwaiPyanwuPchaoshengbo
- 此程序为毕业设计之防火防盗报警器具有MQ2烟雾报警，DS18B20温度报警，红外传感器感应人体红外，超声波感应人得进入，加上1602液晶显示等功能，同时具有蜂鸣器及LED报警-This procedure for the graduation of the fire alarm system design has MQ2 smoke alarm, DS18B20 temperature alarm, human infrared sensor infrared sensor, ultrasoni
ANFANGCHENGXU
- 安防报警程序。红外报警和烟雾报警。可以通过GSM发短信，AT24C02存储电话号码，可更改。-Security alarm program. Infrared alarm and smoke alarm. Can send messages through the GSM, AT24C02 to store phone number, can be changed.
yanwubaoji
- 利用Keil Uvision4阮籍，基于51单片机的烟雾报警程序-Use Keil Uvision4 Ruan, 51 MCU-based smoke alarm program
code
- 烟雾报警代码，采用STM32F103系列嵌入式单片机作为控制对象-fog bell code
smogsensor-protuse
- 烟雾报警装置的protuse仿真 用到AD0832 LCD1602-Protuse simulation of smoke alarm device
chengxu
- 基于51单片机烟雾报警系统，模拟量参考程序-Smoke alarm system based on 51 microcontroller, analog reference program
alarm
- 单片机烟雾报警c程序，给予at89c51开发，源代码，功能强大可以检测各类可燃气体浓度-it is asmoke-alarm project，writing by c++ language
HTK_Project23A-JED-X10-NEW
- HOLTEK测电磁内阻,用于烟雾报警的报警信号来控制继电器-HOTEL test battery resistor
mokedsn
- 这是个火灾逃生报警的仿真和单片机程序，用的是最常用I2C接口的烟雾传感器，这个程序应用在公司项目中应用到，决对可行，包括程序和仿真，请勿用于商用。(This is a microcontroller program simulation and fire escape alarm, smoke sensor is used in the most commonly used I2C interface, applied to the application of the company's pr
1-GSM主程序加烟雾
- 建立了一个基于GSM网络及短信息平台上的家庭安防系统，设计中采用了STC89C52单片机系统、无线GSM短信模块及传感器技术。(The system in this paper has some advantages, such as simple hardware structure and high cost-performance and so on. The Modularized program is convenient to expansion of the system. The
MQ-2烟雾传感器模块
- 烟雾报警资料及代码, 1、传感器先预热20秒左右。 2、将传感器放在无被测气体的地方，顺时针调节电位器，调节到指示灯亮，然后逆时针转半圈，调到指示灯不亮，然后接近被测气体，指示灯亮，离开被测气体，指示灯熄灭，就证明传感器是好的！(Smoke Alarm Data and Code)
智能粮仓管理系统
- 智能粮仓管理系统，用户登录界面，温度，湿度，大气压和烟雾报警
fire_warning
- 传感器有温度传感器和烟雾传感器，分别检测温度浓度和烟雾浓度。当测量的温度或烟雾浓度高于临界值时，单片机将发送信号给声光报警模块产生相应的声光报警。当测量的温度或烟雾浓度低于临界值时，状态指示灯保持常亮，说明火灾报警器在正常通电工作。(Sensors include temperature sensors and smoke sensors, which detect temperature concentration and smoke concentration respectively. W
szw
- 声光报警、显示楼层、oled1602、7段显示数码管(Acousto-optic alarm, display floor, OLED 1602, 7 segment display digital tube)